Warn the operator when people are in the lift zone
How scaffolding crews can warn the operator when people are in the lift zone, with a checklist, steps, tool options and common mistakes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Give the warning through a signal the whole crew has agreed on before the first lift, and keep a second signal ready in case the first one fails. OperatorLink shows STOP, HOLD and SLOW to the crew in a phone browser. [1] STOP ends every move a phone is still sending and shows a full-screen alert to everyone else. [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, and no paid plan is built yet [1] | not published |
| Two-way radio | not published | not published | not published |
| Phone video call app | not published | not published | not published |
What you need before you start
Scaffolding crews need a warning that reaches the operator the moment someone steps into the lift zone, which is the area under and around the load where a moving load can strike people. Decide before the lift who watches the zone, who gives the warning, and who can call a stop. The signal person, the crew member who relays signals to the operator, usually has this job, and that person needs to stand where the operator can see them.
Agree on the signal for people in the zone and make sure every crew member knows it. The operator should be able to see or hear the warning from the cab, so check the view and the noise level before work starts.
If the crew uses phones to pass signals, button presses, chat and voice pass between phones in a browser. [1] The person who starts the session shares a link or QR code, and the rest of the crew joins from it. [1] An empty session is wiped after 3 idle hours, so start a fresh session at the beginning of each shift. [1] Finally, agree on which signals stay on, since HOLD and SLOW stay on for everyone until the last person leaves the jobsite. [1]
Step by step
- Walk the lift zone before the first load moves and mark where people must stand clear.
- Name the signal person and one backup who can give the warning if the signal person cannot see the zone.
- Agree on one signal for people in the zone and one for an immediate stop, and say both out loud at the start of the shift.
- Confirm the operator can see the signal person and the zone from the cab, or can hear the warning over the site noise.
- If the crew uses phones, have each member open the shared link in a phone browser, with no app install needed. [1]
- Before a lift, confirm every phone shows the session and that the crew can see each other's signals. [1]
- When someone enters the lift zone, the signal person gives the warning and the load stops at once. Pressing STOP ends every move a phone is still sending and shows a full-screen alert to everyone else. [1]
- Holding a move button keeps sending that move to the other phones, and if it stops arriving for 2 seconds, the other phones drop it. [1] The signal person watches the load while the button is held.
- The operator does not resume until the signal person confirms the zone is clear and the crew has agreed to go on.
- At the end of the shift, everyone leaves the session, and the next shift starts a fresh one.
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody needs to install an app, because the page runs in a browser. [1] STOP releases held directions on every phone and alerts everyone else, and one-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] [1]
A two-way radio is a second option. No facts here describe one, so check that the signal person can be heard over site noise, that every crew member carries a radio, and that the channel stays clear for the whole lift.
A phone video call app is a third option. No facts here describe one, so check that the signal person's view of the zone stays in the call, that the phone does not lock its screen partway through the lift, and that the crew can keep the call open for the whole shift.
Match the option to the site and the crew, and keep a backup ready.
Common mistakes to avoid
Relying on one phone or one person for the warning, so a dropped signal or a missed glance leaves the zone unwatched. Keep a voice or hand option ready as a backup.
Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every phone. [1]
Leaving an empty session open and expecting it to hold signals the next day. A session with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on for everyone until the last person leaves. [1]
Assuming a move is still reaching the other phones after the button is released. Holding a move button keeps sending that move, and the other phones drop it if it stops arriving for 2 seconds. [1]
Skipping the home screen step. Adding the page to a phone's home screen lets it open as a standalone app. [1]
Frequently asked questions
Is OperatorLink free to use for scaffolding crews?
OperatorLink is currently free to use, and no paid plan is built yet. [1] Button presses, chat and voice pass between phones in a browser. [1]
What does the STOP signal in OperatorLink do when someone enters the lift zone?
STOP ends every move a phone is still sending and shows a full-screen alert to everyone else, so the crew sees it at once. [1] HOLD and SLOW work differently, since they stay on for everyone until the last person leaves the jobsite. [1] Agree before the lift on which signal the signal person gives for people in the zone, and keep a voice or hand backup in place.
How long does an OperatorLink jobsite link stay active for a crew?
A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier shift may no longer open the session. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] Start a fresh session at the beginning of each shift and share the new link or QR code with the crew.
Does OperatorLink buzz every phone when a warning comes in?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone the alert may only be seen on screen. When STOP is pressed, everyone else gets a full-screen alert. [1] Check the sound and screen settings on every phone before the lift so nobody misses the signal.
Can OperatorLink be used for voice calls during a lift?
Anyone who joins the session can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Anyone who joins can take part in a voice call run from the phone browser, so keep a radio or hand signal as a fallback for the signal person. [1]
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift