2Dig Plain comparisons of crane signalling and jobsite communication tools

How to call hold when a hose shifts under pressure

How concrete pump operators call hold when a hose shifts under pressure, with what to have ready, the steps, tool options and common mistakes.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

Stop the pump as soon as the hose moves, call hold so everyone keeps clear, and restart only after the signal person confirms the hose is secured.

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1]Currently free to use, no paid plan built yet [1]not published
Two-way radionot publishednot publishednot published
Phone video call appnot publishednot publishednot published

What you need before you start

Before the pour starts, the crew should agree who calls hold and who can stop the pump, so nobody has to guess when the hose moves.

The signal person needs a clear view of the hose from a safe spot, and the pump operator needs a reliable way to hear or see that call. Everyone on the ground should know where the hose could swing if it shifts, and should stay out of that path.

Check that the hose clamps and couplings are secured before pumping starts, and keep the pump stop control within easy reach of the operator. If the crew uses phones to pass the call, check that each phone has a working connection for the whole pour and that a backup method is agreed in case it fails.

Step by step

Agree these steps with the crew before the pour starts.

  1. Watch the hose at the start of every pour and note where it could swing if it shifts.
  2. When the hose starts to move, the first person who sees it calls hold in a clear voice or the agreed signal.
  3. The pump operator stops the pump so the pressure drops before anyone touches the hose.
  4. Everyone keeps clear of the hose path and holds position until the signal person confirms the hose is steady.
  5. Check the clamps and couplings, and secure the hose again before any pumping restarts.
  6. Restart the pump only after the signal person gives the all clear and the crew has confirmed it.

Tools that can do it

OperatorLink is made by the team that publishes this site, and it shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] Nobody needs to install an app, because the page runs in a browser. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] HOLD stays on for everyone in the jobsite until the last person leaves. [1] OperatorLink is currently free to use, and no paid plan is built yet. [1]

A two-way radio is a second option. No facts here describe one, so check that every crew member can hear the calls over machine noise, that the channel stays clear during the pour, and that the crew agrees on plain words for hold and stop.

A phone video call app is a third option. No facts here describe one, so check whether the signal person can keep the call open for the whole pour, whether the phone stays on screen, and whether the call can be heard over pump noise.

Match the option to the crew and the site, and keep a fallback ready, since a phone browser depends on the phone's connection. [1]

Common mistakes to avoid

Waiting for the hose to move a long way before calling hold. Call it as soon as the hose starts to shift, because the pump can be stopped earlier that way.

Relying on one person to see the hose. Put a second person in view of the line so a single missed movement does not go unnoticed.

Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device. [1]

Forgetting that HOLD stays on until the last person leaves the jobsite, so the crew has to remember it is active while the hose is being secured. [1]

Reusing an old jobsite link. A link stops working 12 hours after the first person joins it. [1]

Leaving an empty session and expecting it to still be there later. A jobsite with nobody in it is wiped after 3 idle hours. [1]

Letting a held move keep going. If a move stops arriving for 2 seconds, the other phones drop it, so keep the button held only while the move is needed. [1]

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser with no app install, so the crew does not need to download anything before the pour. [1] Check that each phone has a working connection for the whole shift, because button presses and calls pass between phones in the browser. [1]

What does HOLD do on OperatorLink when a hose shifts?

HOLD shows to the whole jobsite crew and stays on for everyone until the last person leaves, so it does not clear just because one phone is put down. [1] STOP works differently: it releases every held direction on every phone and shows a full-screen alert to everyone else. [1] When a hose moves under pressure, the crew can send STOP first and then HOLD, and agree in advance who clears it.

How long does an OperatorLink jobsite link last?

A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, the person who starts the jobsite can open a new session and share its link or QR code with the crew, who join from it. [1]

Do STOP signals buzz every phone in the crew?

STOP signals do not buzz on every phone. On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so iPhone users in the crew need to rely on the full-screen alert shown when STOP is pressed. [1] [1] Check the sound and screen on every phone before the pour starts, so nobody misses a signal.

Can the crew talk by voice during a hose problem on OperatorLink?

Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap calls are sent as chat messages. [1] Voice depends on the phone browser and the phone's connection, so keep a radio or hand signal ready as a fallback in case the connection drops. [1]

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons