How to call hold during tight lifts for industrial plant riggers
Steps for calling hold during tight lifts, what industrial plant riggers should have ready, tool options and common mistakes to avoid on site.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
To call hold during a tight lift, agree on one clear signal, make sure everyone on the lift can see or hear it, and confirm it was received before the load moves again. OperatorLink can show HOLD to the crew's phones in a phone browser [1].
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Dedicated signal person with hand signals | not published | not published | not published |
| Two-way radio | not published | not published | not published |
| Phone video call app | not published | not published | not published |
What you need before you start
Before a tight lift, the rigger who may call hold needs a clear way to reach everyone who can move the load. Decide who has that authority before the lift starts, not during it. Agree on the exact word or signal for hold, and make sure every person on the lift knows it. Check that the crew can see the signal person, because a hand signal only helps when it can be seen from where each crew member stands.
If the crew uses phones to share signals, each phone needs a working data connection. Button presses, chat and voice pass between phones in a browser [1]. The person who starts the shared session shares a link or QR code, and the crew joins from it [1]. Decide who keeps the session going, because a jobsite with nobody in it is wiped after 3 idle hours [1].
Step by step
Calling hold follows the same pattern whatever tool carries the signal. Follow these steps for each lift.
- Name the person who may call hold before the lift starts, and make sure that person can see the load and the crew.
- Agree on the single word or signal for hold, and say it aloud or show it before the first move.
- When hold is called, everyone stops the load where it is and keeps clear of the rigging.
- Each crew member confirms the hold by repeating it back or by showing the agreed signal.
- Keep the hold in place until the person who called it says the lift can continue, and only then move again.
- If the crew uses a shared phone session, HOLD stays on for everyone in the jobsite until the last person leaves [1].
- If a move button is held on a phone, that move keeps going to the other phones, and if it stops arriving for 2 seconds, the other phones drop it [1].
- When the load is set and the lift is finished, plan how the shared session will end, since HOLD stays on until the last person leaves [1].
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser [1]. It runs in a phone browser with no app install [1]. The person who starts a jobsite shares a link or QR code, and the crew joins from it [1]. Crew members can also send one-tap radio-style calls such as Go Ahead, Copy That and All Clear, which are sent as chat messages [1].
A dedicated signal person using hand signals is a second option. No facts here describe how that works on a given site, so check that every crew member can see the signal person from where they stand, and that the signal person can see the load at all times.
A two-way radio is a third option. No facts here describe one, so check that the crew agrees on plain voice calls, that each member can be heard over the noise on site, and that the channel stays clear for the whole lift.
A phone video call app is a fourth option. No facts here describe one, so check whether the call can stay open for the whole shift, whether the signal person stays in view, and whether the phone's screen stays on during the lift.
Match the option to the crew and the site, and keep a fallback ready, because signals in a phone browser depend on each phone's data signal.
Common mistakes to avoid
Relying on one signal for everything. If one phone or one person's view is missed, the call may not reach the rigger, so keep a second signal ready. Calling hold without agreeing on who can give the all-clear to move again. Confirm that before the first move. Assuming every phone alerts the same way: on Android browsers, signals such as STOP make the phone buzz, but iPhone Safari ignores the buzz, so check the screen and sound on every device [1]. Leaving a shared session empty and expecting it to be there the next day, when a jobsite with nobody in it is wiped after 3 idle hours [1]. Forgetting that HOLD stays on for everyone until the last person leaves, so the crew may need to end the session to clear it [1]. Using an old link, since a jobsite link stops working 12 hours after the first person joins it, so a new link may be needed for the next shift [1]. Opening the page from a browser tab every time, instead of adding it to the home screen to open as a standalone app [1].
Frequently asked questions
Is OperatorLink free to use?
OperatorLink is currently free to use, and no paid plan is built yet [1]. Because it runs in a phone browser with no app install, each phone still needs a working data signal when using the service [1]. Check the phone's data plan before the shift so the signal does not drop during a lift.
How long does HOLD stay on in OperatorLink?
HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves [1]. A HOLD called early in the shift therefore stays on until the session empties, so the crew should plan how the session ends before the lift starts. STOP works differently: it releases every held direction on every phone and shows a full-screen alert to everyone else [1].
Does the STOP signal reach every phone in an OperatorLink session?
STOP releases every held direction on every phone and shows a full-screen alert to everyone else [1]. Button presses, chat and voice pass between phones in a browser [1]. Keep a voice or hand signal ready as a fallback, and do not rely on one phone alone.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it [1]. A jobsite with nobody in it is wiped after 3 idle hours [1]. The person who starts the jobsite can share a new link or QR code, and the crew joins from it [1].
Does OperatorLink buzz on iPhone when a STOP signal arrives?
On Android browsers, signals such as STOP make the phone buzz, but iPhone Safari ignores the buzz [1]. The full-screen STOP alert shows to everyone else, so that alert on the phone's screen is the signal to watch for. [1] STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] Crew members can also send one-tap calls such as Go Ahead, Copy That and All Clear, which are sent as chat messages [1]. Before a lift, confirm that every phone shows alerts the way the crew expects.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift
- Call hold when a load shifts over water for dam work