2Dig Plain comparisons of crane signalling and jobsite communication tools

Checking crew communication gear before a crane lift

How a crane inspector can check crew signal gear before a lift: what to have ready, the steps, tool choices and common mistakes.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

Before a crane lift, check that every crew member's phone or radio works, test each signal with the whole crew, and agree in advance on who may call STOP. One option covered below is OperatorLink, which shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser. [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1]Currently free to use, no paid plan built yet [1]not published
Phone video call appnot publishednot publishednot published
Two-way radionot publishednot publishednot published

What you need before you start

Before you check the crew's communication gear, have the lift plan, the list of crew members with their roles, and the list of signals the crew uses. Confirm which person is the signal person, who gives the signals to the crane operator, and that the operator can see the signal person at all times. Each crew member needs a working phone or radio with a charged battery and a signal for the whole shift. Decide in advance which signals must reach everyone, such as STOP, and which can come from one person.

If the crew uses OperatorLink, each phone needs a working data signal, because the signals pass between phones in a browser. [1] The person who starts the jobsite shares a link or QR code, and the crew joins from it. [1] That link stops working 12 hours after the first person joins it, so note when the session started and create a new one for a later shift. [1]

Step by step

  1. Gather the lift plan and write down each crew member and their role.
  2. Check each phone or radio for charge, signal, volume, and whether the crew can hear it over machine noise.
  3. Have the signal person give each signal in turn, and have the crane operator confirm each one is received.
  4. Confirm that every device alerts the crew, whether by sound, vibration or screen, and note any device that does not.
  5. Confirm that a hand signal or radio is ready in case a phone loses its signal.
  6. Confirm that the signal person stays in the crane operator's view for the whole lift.
  7. Agree on who may call STOP, and make sure everyone understands that STOP comes before any other signal.
  8. Confirm that the session link or code in use is the current one for this jobsite and not one left over from an earlier shift.
  9. Record the time of the check, and repeat it whenever a crew member changes phones or the crew changes.
  10. Before the lift starts, confirm that everyone is present and can see the signals.

Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] It runs in a phone browser with no app install. [1] When STOP is pressed, it ends every move a phone is still sending and shows a full-screen alert to everyone else. [1]

A phone video call app is a second option. No source here describes one, so before choosing it, check whether the crew can keep the call open for the whole shift, whether the signal person stays in view, and whether the phone locks its screen during a lift.

A two-way radio is a third option. No source here describes one, so before choosing it, check that the crew agrees on plain voice calls, that every member can be heard over machine noise, and that the channel stays clear for the whole lift.

Match the option to the crew and the site, and keep a fallback ready in case a phone loses its signal.

Common mistakes to avoid

Relying on one phone for STOP: if that phone loses its signal, the rest of the crew may not receive the signal, so keep a voice or hand option ready.

Assuming every phone alerts the same way: on Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check sound and screen on every device. [1]

Leaving a session open between shifts: a jobsite with nobody in it is wiped after 3 idle hours. [1]

Forgetting that HOLD and SLOW stay on for everyone until the last person leaves, so a HOLD left on from an earlier part of the shift keeps showing to the crew. [1]

Not confirming that a move still arrives: holding a move button keeps sending that move to the other phones, and if it stops arriving for 2 seconds, the other phones drop it. [1]

Letting a phone go to sleep during the lift without checking that it is still in the session. The app can be added to a phone's home screen as a standalone app, which some crews set up before the shift. [1]

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet. [1] Because it runs in a phone browser, the phones need a working data signal for the whole shift. [1] Before relying on it for a lift, check that each crew member's phone has a data signal where the crew will be working, and keep a radio or hand signal ready as a backup.

What happens when STOP is pressed in OperatorLink?

STOP ends every move a phone is still sending and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, because they stay on for everyone in the jobsite until the last person leaves. [1] Before the lift begins, have each crew member confirm that their phone shows the alert when a test signal is given, so no one misses it during the lift.

How long does an OperatorLink jobsite link stay active?

A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, start a new session and share its link or QR code with the crew. [1] Write down when the session started so you can tell whether a link is still current.

Do OperatorLink signals buzz on every phone?

On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone, check the screen and sound before the lift rather than relying on a buzz. Check the sound and screen settings on every phone in the crew, and confirm that each person has seen a test signal before the lift starts.

Can OperatorLink handle voice calls during a lift?

Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Because voice runs through the phone browser, keep a radio or hand signal as a fallback in case a phone loses its signal. [1]

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons