How to verify comms gear before a crane ships to site
Steps for crane rental fleet managers to check comms gear before a crane ships to a jobsite, with what to have ready and common mistakes to avoid.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Before a crane ships, check that each comms device works on the phones and radios the crew will carry, and test all of it at the yard first. For a phone-based option, OperatorLink shows STOP, HOLD and SLOW to the crew and runs in a phone browser. [1] [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser [1] | Free to use right now, and no paid plan is built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Before a crane ships, the fleet manager needs a list of every comms device that will go to site, the name of the person who will carry each one, and a test area at the yard where the gear can be switched on and checked. The signals that matter on a crane job are the ones the ground crew uses with the operator, such as STOP, HOLD and SLOW, so the list should show which device carries each signal.
Any phone-based option needs a working browser and a data signal, because the signals travel between phones in a browser. [1] One person needs to be named to start the session and share the link or QR code, and that person should be able to do it before the crane leaves the yard. [1] Check that every phone can open the session and show alerts, since on Android browsers signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] Keep a backup signal ready in case a phone drops out during the lift.
Step by step
These steps apply to any comms gear. Where a step mentions a phone browser, it refers to the OperatorLink option.
- Write down every comms device that will go on the crane and to the site, and who carries each one.
- Charge each device and check that it holds its charge for a full shift.
- Check that each phone can open a phone browser and has a working data signal where the crane will work. [1]
- Open the session from a phone browser, with no app install needed. [1]
- Share the link or QR code with the test crew, and confirm that each person joins from it. [1]
- Press STOP on one phone and confirm that every other phone shows the full-screen alert. [1]
- Press HOLD and then SLOW, and confirm that both stay on for everyone until the last person leaves. [1]
- Hold a move button and confirm that the move reaches the other phones. If it stops arriving for 2 seconds, the other phones drop it, so check that the crew notices the drop. [1]
- Test the one-tap calls and the voice call. Go Ahead, Copy That and All Clear are sent as chat messages, and anyone who joins can take part in a voice call from the phone browser. [1] [1]
- Check the sound and screen on each phone, leave the session, and start a fresh session for the real shift. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] Nobody needs to install an app, since the page runs in a browser. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] A jobsite link stops working 12 hours after the first person joins it, so each shift needs its own link. [1] The app can also be added to a phone's home screen as a standalone app. [1] OperatorLink is currently free to use, and no paid plan is built yet. [1]
A phone video call app is a second option. No facts are available here about how one works, so check whether the crew can keep the call open for the whole shift, whether the signal person stays in view, and whether the phone locks its screen during a lift.
A two-way radio is a third option. No facts are available here about how one works, so check that the crew agrees on plain voice calls, that every member can be heard over machine noise, and that the channel stays clear through the lift.
Match the option to the crew and the site, and keep a fallback ready in case a phone's data signal drops.
Common mistakes to avoid
Relying on one phone for the STOP signal. If that phone loses its data signal, the rest of the crew may not see the signal, so keep a voice or hand option ready.
Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device. [1]
Leaving an empty session open and expecting it to still work the next day. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on for everyone until the last person leaves. [1]
Using a link from an earlier shift. A jobsite link stops working 12 hours after the first person joins it. [1]
Not checking that moves still arrive. Holding a move button keeps sending that move, and if it stops arriving for 2 seconds, the other phones drop it. [1]
Testing only in the yard and assuming the same signal at the site. Run the final check where the crane will work.
Frequently asked questions
Is OperatorLink free to use?
OperatorLink is currently free to use, and no paid plan is built yet. [1] Because it runs in a phone browser, each phone still needs a working data signal at the site, so test that before the crane ships. Nothing needs to be installed as an app, so the check can be done on the same phones the crew will carry. [1]
What happens when STOP is pressed on OperatorLink?
STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, since they stay on for everyone until the last person leaves the jobsite. [1] Test all of these signals at the yard so the crew knows what each one looks like on screen before the lift.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For each shift, start a new session and share the new link or QR code with the crew, so nobody tries to join with a link that has stopped working.
Do STOP alerts buzz on every phone with OperatorLink?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone the full-screen alert is the signal to watch for. [1] Check the sound and screen settings on each phone before the crane ships, and make sure the crew knows which phones will buzz and which will not.
Can the crew talk during a lift with OperatorLink?
Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Because the phone browser needs a working data signal, keep a hand signal or radio ready as a fallback during the lift. [1]
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift