How precast installers send STOP when a panel swings
Send a STOP signal to a crew when a precast panel swings: what to have ready, steps, tool options and common mistakes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
The signal person sends STOP to the whole crew, and everyone stops and looks before moving again. OperatorLink is one option for that: its STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] Keep a voice or hand backup ready in case a phone loses its signal.
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, with no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
| Hand signals with a spotter | not published | not published | not published |
What you need before you start
Before the panel moves, the crew needs one signal person who gives every call, plus a backup who can take over if that person is out of view. Every installer on the lift should know who that person is and what STOP, HOLD and SLOW look like from where they stand.
Check each phone too. It needs a working data signal and a screen that stays on for the whole lift, since the signals pass between phones over the phone network. [1] If you plan to share a link or QR code with the crew, the person who starts the session must have it ready before the lift begins. [1] A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier shift may not open. [1]
Finally, agree in advance on what each signal means and what each installer does when STOP arrives, because a signal that is sent but not acted on does not stop a panel.
Step by step
- Walk the lift plan with the crew and name the signal person, plus one backup.
- Confirm every installer has a phone that can open a web page and has a working data signal for the whole lift.
- Get everyone into the same signal channel before the panel leaves the ground, and confirm each person can see and hear the signals.
- Agree on the meaning of STOP, HOLD and SLOW, and write them on a card that stays with the crew.
- Send a practice signal with no load on the hook, and check that every phone receives it.
- Keep the signal person in view of the panel and the installers, and send movement signals only as the lift needs them.
- When the panel swings or anyone sees a problem, the signal person sends STOP, and everyone stops and looks before moving again.
- At the end of the shift, everyone leaves the session, and the signal person checks that nobody is still in it.
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] It needs no app install, because the crew opens it in the browser. [1] The person who starts the jobsite shares a link or QR code, and the crew joins from it. [1] Holding a move button keeps that move going to the other phones, and if the move stops arriving for 2 seconds, the other phones drop it. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1]
A phone video call app is a second option. This page has no published details for it, so check whether the call stays open for the whole lift, whether the signal person stays in view of the panel, and whether the phone's screen locks during the lift.
A two-way radio is a third option. This page has no published details for it, so check that every installer can hear the calls over the noise on site, and that the channel stays clear for the whole lift.
Hand signals with a spotter are a fourth option, and no published details are available here. Check that the spotter can see every installer and the panel from a fixed position, and that the signals are agreed before the shift.
Match the option to the crew and the site, and keep a fallback ready, since a phone browser depends on the phone's data signal. [1]
Common mistakes to avoid
Relying on one phone for STOP is a gap to avoid. If that phone loses its data signal, the rest of the crew may not receive the signal, so keep a voice or hand option ready for the same call.
Assuming every phone alerts the same way causes trouble. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device. [1]
Reusing a link from an earlier shift is another mistake. A jobsite link stops working 12 hours after the first person joins it, so start a fresh session for each shift. [1]
Leaving an empty session and expecting it to be there later fails too, because a jobsite with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on for everyone until the last person leaves can mean a move is made under a signal that no longer applies, so check the screen for HOLD and SLOW before any move. [1]
Letting go of a move button while the panel still moves is risky. A move that stops arriving for 2 seconds is dropped by the other phones, so keep the button held only while the move is needed. [1]
Relying on a phone signal in place of a trained signal person is a mistake. The signal person still watches the panel and decides when a call is needed.
Frequently asked questions
Is OperatorLink free to use for precast crews?
OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser, so there is no app to install, but each installer still needs a phone with a working data signal for the lift. [1] Check each crew member's phone before the shift, since the signals pass over that connection. [1]
What happens when someone presses STOP in OperatorLink?
STOP releases every held direction on every phone and shows a full-screen alert to everyone else in the jobsite. [1] HOLD and SLOW behave differently, because they stay on for everyone until the last person leaves the jobsite. [1] Keep that difference in mind when deciding which signal ends a lift, and make sure every installer knows what each one means before the panel moves.
How long does an OperatorLink jobsite link last?
A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier shift may no longer open the jobsite. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, the person who starts the jobsite can share a fresh link or QR code with the crew. [1]
Do STOP signals buzz on iPhones with OperatorLink?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone the alert has to be seen on the screen rather than felt. [1] Check the sound and screen settings on every phone in the crew before the lift, so nobody misses a STOP. Do this for the whole crew, not only the signal person.
Can OperatorLink be used to talk during a panel swing?
Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Because these calls travel over the phone's data signal, keep a hand signal or radio ready as a fallback for the lift. [1]
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift