How to relay load signals between deck and cab for offshore crane crews
Steps, tool options and common mistakes for passing STOP, HOLD and SLOW signals between the deck crew and the cab on offshore cranes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Relaying load signals between deck and cab means the signal person's instructions reach the crane operator in the cab clearly and in time. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Agree the signals before the lift and keep a radio or hand signal ready as a fallback.
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Two-way radio | not published | not published | not published |
| Hand signals from a signal person | not published | not published | not published |
| Phone video call app | not published | not published | not published |
What you need before you start
Load signals between deck and cab work best when the crew agrees what each signal means before the lift starts and each person knows who gives it and who acts on it. Offshore, the data signal may be weak or absent, so check coverage on the deck and in the cab before relying on phones. Check that every phone has a working browser for the whole shift, because OperatorLink passes signals between phones in a browser. [1] Ask whoever will start the jobsite to be ready to share a link or QR code with the crew, since the crew joins from it. [1] Plan for the session to end, because a jobsite with nobody in it is wiped after 3 idle hours. [1] Keep a radio or hand signal ready as well, in case the phone link is lost.
Step by step
- Agree the signal set before the lift, covering STOP, HOLD, SLOW and the crew's usual hand signals, and write down who sends each one.
- Test each phone's browser before anyone goes up, since the signals run in a phone browser with no app install. [1]
- Have the person who starts the jobsite share the link or QR code, and confirm every crew member has joined. [1]
- Confirm the cab phone shows the same signals as the deck phones. [1]
- Agree what happens to HOLD and SLOW, since they stay on for everyone until the last person leaves the jobsite. [1]
- Explain that holding a move button keeps sending that move, and if it stops arriving for 2 seconds the other phones drop it, so the signal person keeps the button held while the load moves. [1]
- Make the STOP rule clear: anyone who sees a hazard presses STOP, which releases every held direction on every phone and shows a full-screen alert to everyone else. [1]
- Use one-tap calls for short replies such as Go Ahead, Copy That and All Clear, which are sent as chat messages. [1]
- At the end of the shift, everyone leaves the session, since a jobsite with nobody in it is wiped after 3 idle hours. [1]
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Anyone who joins can take part in a voice call run from the phone browser. [1] It is currently free to use, and no paid plan is built yet. [1]
A two-way radio is a second option. No facts on this page describe one, so check the radio's range from the deck to the cab, whether the crew can hear each other over machine noise, and whether the channel stays clear through the lift.
Hand signals from a signal person are a third option. No facts on this page describe that method either, so check that the signal person can be seen from the cab at every point in the lift and that the crew agrees on one signal for each move.
A phone video call app is a fourth option. Check whether the call can stay open for the whole shift and whether the phone locks its screen during the lift.
Match the option to the crew and the site, and keep a fallback ready in case the phones lose signal offshore.
Common mistakes to avoid
Relying on a single phone for every signal, so a dropped connection leaves the crew without a signal. Keep a radio or hand signal ready.
Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device. [1]
Reusing an old link from an earlier shift. A jobsite link stops working 12 hours after the first person joins it. [1]
Leaving an empty session and expecting it to hold signals the next day. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on until the last person leaves, so the crew has to plan how they are cleared. [1]
Letting a move button go before the move is finished. If a held move stops arriving for 2 seconds, the other phones drop it. [1]
Leaving the phone screen to lock during the lift. Check the lock settings before the shift so the signals stay in view.
Frequently asked questions
Is OperatorLink free to use for offshore crane crews?
OperatorLink is currently free to use, and no paid plan is built yet. [1] Because the signals run in a phone browser, check the phones' signal coverage on the deck and in the cab before the shift. Keep a radio or hand signal ready as a fallback for any shift where the phones cannot connect.
What does OperatorLink do when STOP is pressed on the deck?
STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, since they stay on for everyone until the last person leaves the jobsite. [1] Crews should agree before the lift what happens to HOLD and SLOW at the end of the shift.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, the person who starts the jobsite should open a fresh session and share the new link or QR code with the crew. [1]
Does OperatorLink make every phone buzz when STOP is sent?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so an iPhone may only show the alert on screen. [1] Check the sound and screen settings on every phone before the lift, and agree on a backup, such as a voice call or a hand signal, so nobody relies on a buzz alone.
Can OperatorLink voice calls run during a lift?
Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Keep a radio or hand signal as a fallback in case the phone link is lost, and test the voice call before the lift starts.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift