How to Relay Landing Clearances to a Crane Operator
Learn how elevator installers can relay landing clearances to a crane operator, prepare the crew, confirm each message and compare communication tools.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
To relay clearances from elevator landings to a crane operator, agree on the landing names, clearance information, measurement units and communication method before the lift. Send one clearance at a time, identify the landing, state the information clearly and ask the operator to repeat it back. Keep the crew informed when a clearance changes. OperatorLink is one option for showing STOP, HOLD and SLOW and passing button presses, chat and voice between phones in a phone browser. [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser. [1] | Currently free to use, no paid plan built yet. [1] | not published |
| Two-way radio | not published | not published | not published |
| Hand signals | not published | not published | not published |
| Phone video call app | not published | not published | not published |
What you need before you start
Before relaying clearances from elevator landings to the crane operator, get the landing information and communication arrangements ready. The crew needs a shared way to identify each landing, so a message about one floor is not mistaken for another. Agree on the names or labels used on the job and use the same ones throughout the lift.
Have the clearance information available in the form required by the job's lifting procedure. This includes the stated measurement and its unit. Do not estimate a clearance or substitute an unconfirmed measurement. If information is missing or unclear, have it checked before passing it on.
Agree on who is responsible for sending the information and who will confirm that it has been received. The crane operator needs to know which landing a message concerns and whether it is a new clearance or a correction to an earlier one.
Choose the communication method before work starts. Consider the distance between the landings and the crane, background noise, phone reception and whether the crew can keep the chosen method available throughout the lift.
Make sure the people involved understand the agreed words for STOP, HOLD and SLOW. If a phone-based method is being considered, check the phones and browser access before the crew begins. OperatorLink runs in a phone browser without an app install. [1]
Step by step
- Identify the landing. Before sending a clearance, identify the landing using the name or label agreed by the crew. Do not assume the operator knows which floor is being discussed from the surrounding conversation.
- Check the information. Refer to the clearance information supplied for the job. Confirm that the measurement and its unit are clear. If the information is incomplete, inconsistent or difficult to read, ask for clarification instead of passing on a guess.
- Get the operator's attention. Use the communication method agreed before the lift. Identify the intended recipient and wait for acknowledgment before giving information that requires the operator's attention.
- State one clearance clearly. Give the landing identification first, followed by the clearance information and its unit. Keep separate landings as separate messages. This helps the operator distinguish one location from another.
- Ask for a repeat-back. Have the operator repeat the landing identification and clearance information. Compare the response with the information supplied for the job. If the details do not match, correct the message and obtain confirmation again.
- Confirm the status. Make clear whether the information is current, has changed or needs checking. Do not allow an earlier message to be treated as current after a correction has been issued.
- Pass on changes. When a landing clearance changes, identify the landing again and clearly say that the information is being updated. Give the corrected information and ask the operator to repeat it back. Make sure the relevant crew members receive the correction too.
- Use agreed stop and hold signals. The crew should know how to communicate STOP and HOLD without confusing them with ordinary clearance messages. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew. [1] STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1]
- Keep communication open. Check that the communication method remains available while the work continues. If a message is missed, unclear or interrupted, do not assume it was received. Re-establish communication and confirm the information before proceeding under the job's agreed procedure.
- Close out the information. At the end of the lift, make sure the crew knows that the clearance messages are no longer current for the next operation. Identify any information that needs checking again before another lift begins.
Tools that can do it
The communication method needs to let the crew identify a landing, pass its clearance information and confirm that the operator received the message. The available choices depend on the site, the distance involved and the agreed lifting procedure.
OperatorLink
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] Nobody needs to install an app; the page runs in a browser. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1]
STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1] Holding a move button keeps sending that move to the other phones; if it stops arriving for 2 seconds, they drop it. [1] Anyone who joins can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] OperatorLink is currently free to use, and no paid plan is built yet. [1]
Two-way radio
A two-way radio is another option to consider. No facts here describe a particular radio, so check its operating range at the site, how the crew identifies each landing and how the operator confirms each clearance. Agree on the words used for corrections and stop messages before the lift.
Hand signals
Hand signals are another communication method to consider. No facts here describe a particular hand-signal arrangement, so check which signals the crew will use, where the signal person will stand and whether the operator can see the signals from the working position. Agree on what happens when the operator cannot see the signal person.
Phone video call app
A phone video call app is another option. No facts here describe a particular app, so check whether the crew can keep the call open, whether the relevant person remains visible and whether the operator can hear and understand the clearance messages. Check how the crew will communicate a correction or STOP message.
A communication method should be agreed before the lift rather than selected while a clearance is waiting to be confirmed.
Common mistakes to avoid
Using floor numbers without agreeing on landing names can cause confusion when different crew members use different labels. Agree on the identification for every landing before the lift and use it consistently.
Passing on a measurement without its unit leaves room for misunderstanding. State the measurement and unit together, and ask the operator to repeat both back.
Treating an acknowledgment as confirmation of the full message is another mistake. Ask the operator to repeat the landing and clearance information, then compare it with the information supplied for the job.
Failing to identify a correction can leave an earlier clearance in use. Say clearly that the information has changed, identify the landing again and give the corrected information.
Assuming that a phone alert works the same way on every device can also cause problems. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] Check the screen and alert behavior on the phones being used.
Leaving an empty OperatorLink jobsite open for another shift can also cause confusion. A jobsite with nobody in it is wiped after 3 idle hours. [1] Start a fresh session when needed and share its new link or QR code with the crew. [1]
Frequently asked questions
How should elevator installers relay landing clearances to a crane operator?
Agree on landing names and the clearance information before the lift. Identify the landing first, state the clearance and its unit, then ask the crane operator to repeat the information. Check the response against the information supplied for the job. If a clearance changes, identify the landing again and clearly state that the new message replaces the earlier information.
What information should be included in a landing clearance message?
A clearance message should identify the landing and give the clearance information in the form required by the job. State the measurement and its unit together. Make clear whether the message is the current information or a correction. If the measurement or landing identification is uncertain, have it checked before passing it to the crane operator.
Can OperatorLink relay clearance messages between elevator installers and a crane operator?
OperatorLink passes button presses, chat and voice between phones in a phone browser. [1] Anyone who joins can take part in a voice call, and one-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] [1] The crew still needs to agree on landing names, clearance wording and confirmation procedures.
Can OperatorLink show STOP and HOLD to the crane crew?
OperatorLink shows STOP, HOLD and SLOW to the jobsite crew. [1] When STOP is pressed, every held direction is released on every phone and everyone else sees a full-screen alert. [1] HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1]
Does OperatorLink need to be installed on each crew member's phone?
No app install is needed because OperatorLink runs in a phone browser. [1] The person who starts the jobsite shares a link or QR code, and the crew joins from it. [1] The page can also be added to a phone's home screen as a standalone app. [1]
How long does an OperatorLink jobsite stay available?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, start a fresh jobsite and share its new link or QR code with the crew.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift