How to record communication faults on site for crane inspectors
Steps for crane inspectors to record communication faults found on site, what to have ready, and what to check in each option.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Crane inspectors record communication faults found on site by writing each one down as it happens. Each entry should show the time, the signal, the people involved and what the crew did next, so the fault can be reviewed later.
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1] [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Set up a written record before the lift starts, since a fault is easiest to describe while it is fresh. A notebook, a printed log sheet or a notes app on a phone all work, as long as each entry is written at the time. Each entry needs the date, the time, the jobsite location, the lift being made and the load. Note who gave each signal and who received it, what was given, and what was heard or seen. Leave room for what went wrong, such as a signal that was late, missed, repeated or unclear, and for what the crew did next.
Check the phones before the shift starts. If the crew uses a phone tool to pass signals, button presses, chat and voice pass between phones in a browser. [1] A dead spot on the site is itself worth recording, so test the signal at the lift position. Copy any notes you need out of a shared session before anyone leaves it, because a jobsite with nobody in it is wiped after 3 idle hours. [1]
Step by step
- Agree before the lift who keeps the record and who gives the signals, and write both names at the top of the log.
- Check that each person giving or receiving a signal can see or hear it from where they stand, and note any spot where that fails.
- For each signal, record the time, the signal, who gave it and who acted on it.
- When a signal is missed, late, repeated or unclear, write down what was seen or heard and what the crew did next, while the lift is still under way.
- If a phone carries the signals, watch for moves that stop. Holding a move button keeps that move going to the other phones, and if it stops arriving for 2 seconds, the other phones drop it, so note any move that dropped. [1]
- Before closing the log, go over the entries with each person who was on the lift, so no fault is written from one view only.
- Save the finished log somewhere other than a shared session, and check that each entry has a time, a name and a result.
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody needs to install an app, because the page runs in a browser. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] A jobsite link stops working 12 hours after the first person joins it, so a later shift needs a new link. [1] This page has no details on whether chat or signals leave a copy that can be kept, so check that before relying on them as the written record.
A phone video call app is a second option. No facts here describe one, so check whether the call can stay open for the whole shift, whether the person giving signals stays in view, and whether the phone keeps its screen on during a lift.
A two-way radio is a third option. No facts here describe one, so check that the crew agrees on plain spoken signals, that every member can be heard over site noise, and that the channel stays clear through the lift.
Match the option to the crew and the site, and keep a fallback ready in case a phone loses its signal.
Common mistakes to avoid
Relying on a single note written later, when details have faded. Write each entry as the signal happens.
Trusting a phone alert without checking it on every device. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and the screen on each phone. [1]
Forgetting that HOLD and SLOW stay on for everyone until the last person leaves, so the crew has to clear them on purpose and the log should show when they were cleared. [1]
Leaving a session empty and assuming it will still be there the next day. An empty jobsite is wiped after 3 idle hours. [1]
Reusing a link from an earlier shift. A link stops working 12 hours after the first person joins it. [1]
Writing down a dropped move as a crew error without checking it. If a held move stops arriving for 2 seconds, the other phones drop it. [1]
Frequently asked questions
Is OperatorLink free to use for crane inspectors?
OperatorLink is currently free to use, and no paid plan is built yet. [1] The page runs in a phone browser, so no app install is needed. [1] Check each phone's signal before the shift starts and keep a fallback ready in case one drops out. Since the page has no details on paid features, check the current terms before planning around any cost.
What happens when STOP is pressed in OperatorLink?
STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] HOLD and SLOW work differently, because they stay on for everyone in the jobsite and are cleared only when the last person leaves. [1] For the written record, note the time of each STOP and who pressed it in the crew's own log, since this page has no details on how STOP is logged.
How long does an OperatorLink jobsite link last?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a later shift, the person who starts the jobsite needs to share a new link or QR code with the crew, and the crew joins from it. [1]
Do STOP signals buzz on every phone with OperatorLink?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone the crew must rely on the screen to notice the alert. [1] Check the sound and screen settings on every phone in the crew before the lift, so nobody misses a signal. Adding the page to the home screen lets it open as a standalone app. [1]
Can crew members talk by voice in OperatorLink during a lift?
Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Check each phone's signal before the lift, and keep a radio or hand signal ready as a fallback. This page has no details on whether voice calls are recorded, so check that before relying on a call for the written record.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift