Pass hold and slow commands during hull assembly
Steps for passing hold and slow commands during hull assembly, with what to ready, three tool options and mistakes to avoid on the yard floor.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Pass hold and slow commands by agreeing on who gives each signal, which phones show them, and how each one is cleared before the lift. OperatorLink is one option: it shows STOP, HOLD and SLOW to the crew in a phone browser. [1] It is currently free to use, and no paid plan is built yet. [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Before the first lift, settle who gives the signals and who sees them, because hull assembly often involves several riggers working on different sides of the work. Each person who needs to see the signals needs a phone with a working browser and a data signal for the whole shift. [1] Check that the signal holds in the spots where the hull blocks the view between riggers.
Decide who starts the session, since that person shares a link or QR code and the rest of the crew joins from it. [1] A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier shift may not open the session. [1]
Decide which phone shows HOLD and SLOW, because those two signals stay on for everyone in the session until the last person leaves. [1] Keep a spoken or hand signal ready as a backup in case a phone drops out.
Step by step
- Charge each phone and check its data signal before the shift starts, since the signals pass between phones in a browser. [1]
- Have the person who starts the session open it from a phone browser. No app install is needed. [1]
- Share the link or QR code with the crew, and have each rigger join from it. [1]
- Confirm every rigger is in the session before the first lift, so each person sees the same signals. [1]
- Agree on what HOLD and SLOW mean before the lift, and agree on who sets them and who checks they are off. HOLD and SLOW stay on for everyone until the last person leaves the session. [1]
- When a move is passed by holding a button, keep the button pressed, because holding it keeps sending that move to the other phones, and if the move stops arriving for 2 seconds, they drop it. [1]
- When anyone presses STOP, every held direction is released on every phone and everyone else sees a full-screen alert, so pause and look before moving again. [1]
- Use the quick calls for short replies such as Go Ahead, Copy That and All Clear, which are sent as chat messages. [1]
- At the end of the shift, have everyone leave the session. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody needs to install an app, since the page runs in the browser, and it can be added to a phone's home screen as a standalone app. [1] [1] Anyone who joins can take part in a voice call run from the phone browser. [1] On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1]
A phone video call app is a second option. Nothing on this page describes one, so check whether the call can stay open for the whole assembly, whether the rigger on the hull can keep the screen in view, and whether the phone locks its screen during a lift.
A two-way radio is a third option. Nothing on this page describes one, so check that every rigger can hear the call over yard noise, that the crew agrees on plain spoken words, and that the channel stays clear through the lift.
Match the option to the crew and the yard, and keep a fallback ready in case a phone loses its signal.
Common mistakes to avoid
Relying on one phone to show every signal. If that phone loses its data signal, the rest of the crew may not see the change, so keep a spoken or hand signal ready.
Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on each device. [1]
Reusing a link from a previous shift. A jobsite link stops working 12 hours after the first person joins it. [1]
Leaving the session empty and expecting it to be there the next day. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on until the last person leaves. [1]
Letting go of a move button and assuming the move still runs. If a move stops arriving for 2 seconds, the other phones drop it. [1]
Frequently asked questions
Is OperatorLink free to use for shipyard riggers?
OperatorLink is currently free to use, and no paid plan is built yet. [1] The page runs in a phone browser, so each rigger's phone uses its own data for the shift. [1] Check the phone's data plan before the first lift so the signal does not run out partway through the work.
What happens when someone presses STOP during hull assembly in OperatorLink?
STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [1] HOLD and SLOW work differently: they stay on for everyone until the last person leaves the session. [1] Because the alert is shown on screen, the crew can see a stop at once, but check the screens and the sound on each phone before the lift starts.
How long does an OperatorLink jobsite link stay usable for shipyard riggers?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours, so a session left over from an earlier shift may be gone. [1] For each new shift, start a fresh session and share the new link or QR code with the crew. [1]
Do STOP alerts buzz on every phone during hull work in OperatorLink?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so an iPhone may only show the signal on screen. [1] Before the lift, check the sound and screen on each phone, and note which riggers carry an iPhone so the crew can plan how they will notice a stop.
Can riggers talk to each other during a lift using OperatorLink?
Anyone who joins the session can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Keep a spoken or hand signal ready as a backup in case a phone drops out during the lift.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift