How to monitor student operators on a shared jobsite channel
Set up one shared session that every student operator joins, then watch their signals and chat for the whole training shift.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
OperatorLink runs in a phone browser with no app install. [1] [1] OperatorLink is one option for that. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Before the session starts, the instructor needs a phone with a working browser and a data signal, because button presses, chat and voice pass between phones in a browser. [1] Make a list of every student operator on the shift and their phone, so nobody is missed when the group joins. Choose one person to start the session and share its link or QR code, since everyone else joins from that link. [1] Keep the link handy until the last student has joined, because a link stops working 12 hours after the first person joins it. [1] Agree in advance which signals stay on for the whole session, because HOLD and SLOW remain for everyone until the last person leaves. [1] Write down a fallback for a dead phone or a lost signal, such as a hand signal the students already know or a voice radio, and rehearse it before any lift. Finally, check that each student's phone can keep its screen on during training, because a phone that sleeps mid-session may not show what is happening.
Step by step
- Pick one session that the instructor and every student operator can join.
- Check that each phone has a working browser and a data signal for the whole session.
- Have the person who starts the session share the link or QR code with the group.
- Confirm every student is in the session before the first lift, so everyone is looking at the same signals.
- Agree on the meaning of each signal, such as STOP, HOLD and SLOW, and make sure every student can explain what each one asks them to do.
- Run a short check with no load to confirm that each phone shows the same signal when one is sent.
- During the lift, watch the signals and the chat for each student's moves, and pause the lift if a move is unclear or a signal seems to be missing.
- At the end of the session, have everyone leave, then note any signal that did not arrive so the next session can be planned around it.
Run the same steps for each new session, because a session left with nobody in it does not carry over. Keep a short written record of the signals used, the phones involved and any problems, so the instructor can review the session later.
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody needs to install an app, because the page runs in a browser. [1] The person who starts the session shares a link or QR code, and the group joins from it. [1] STOP cancels every movement that a phone is still holding, on every phone, and shows a full-screen alert to everyone else. [1] Anyone who joins can take part in a voice call run from the phone browser, and one-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] [1]
A phone video call app is a second option. Published details for this option are not included here, so check whether the group can keep the call open for the whole session, whether the instructor can see each student's hands and the load, and whether the phone locks its screen during a lift.
A two-way radio is a third option. Published details for it are not included here, so check that the group agrees on plain voice calls, that every student can be heard over machine noise, and that the channel stays clear through the lift.
Match the option to the crew and the site, and keep a fallback ready, since a phone browser depends on each phone having a data signal. [1]
Common mistakes to avoid
Relying on one phone for the STOP signal. If that phone loses its data signal, it cannot send or receive signals through the browser, so keep a voice or hand signal ready for the whole crew. [1]
Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device before the first lift. [1]
Leaving a session empty and expecting it to be ready the next day. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on until the last person leaves. Students who step away do not clear them, so the instructor should confirm the signal state before each move. [1]
Letting a move button go without checking the result. A move only keeps sending while the button is held, and if it stops arriving for 2 seconds, the other phones drop it. [1]
Skipping the home screen install. Adding the page to the home screen lets it open as a standalone app, so the setup choice should be made before training starts. [1]
Frequently asked questions
Is OperatorLink free to use?
OperatorLink is currently free to use, and no paid plan is built yet. [1] Because it runs in a phone browser, each phone still needs a working data signal for the whole session. [1] Check the data plan on each student's phone before training, since a limit on data could interrupt the session. Nothing published here covers how a data plan works, so confirm those details with each phone provider.
What happens when someone presses STOP in OperatorLink?
STOP cancels every movement each phone in the session is still holding and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, because they stay on for everyone until the last person leaves the jobsite. [1] Practice what each signal means before the first lift, so students know how to respond when STOP appears on their screen.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] Share the link near the start of the shift, and keep it handy until the last student has joined. For a later session, start a new one and share its link or QR code with the group.
Do STOP signals buzz every phone in OperatorLink?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so an iPhone may only show the alert on its screen. [1] Check the sound, vibration and screen settings on every phone before the session starts, and make sure every student knows that an iPhone may show a STOP only on screen.
Can OperatorLink be used for voice calls during a crane lift?
Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] Voice depends on each phone's data signal, so keep a hand signal or radio as a fallback. Check that every student can hear the call over the site noise, because nothing published here covers noise levels.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift