Keep voice contact in wind and engine noise for offshore crane crews
How offshore crane crews keep voice contact in wind and engine noise, with what to prepare, steps, tool options and common mistakes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Before the lift, agree on one voice method, the phrases the crew will use, and a fallback signal, then test the call in the actual wind and engine noise on site. OperatorLink is one option for voice between phones in a browser, and anyone who joins can take part in its voice call. [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Anyone who joins can take part in a voice call run from the phone browser, and one-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages [1] [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Offshore crane crews need a plan for voice before the lift starts, because wind and engine noise can cover both a voice call and a radio call. Button presses, chat and voice pass between phones in a browser. [1] Decide who starts the session and who shares the link or QR code, because the rest of the crew joins from that link. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Keep a hand signal or a radio ready as a fallback, and check that each phone's sound and screen can be used in the noise on the actual site. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Step by step
- Name the person who calls the lift and the person who gives the voice commands, so each call has one clear source.
- Test each phone's sound at the crane position before the first lift, with the engine running and the wind blowing.
- Agree on the short phrases the crew will use, such as Go Ahead, Copy That and All Clear, and say what each one means.
- Agree on one main voice channel and one fallback signal, such as a hand signal or a radio, and make sure everyone knows which one is which.
- Confirm that every crew member can hear the call and see the screen before the load moves.
- Keep the call open for the whole lift, and have the receiver repeat each command back before acting on it.
- Confirm the load has stopped before any new move is called.
- If a command is unclear or a voice cuts out, stop the move and repeat the command until everyone confirms it.
- At the end of the shift, close the call and confirm that every crew member has left the session, so no one is left waiting on a call that has ended.
Tools that can do it
OperatorLink is made by the team that publishes this site. Anyone who joins the session can take part in a voice call run from the phone browser, and one-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] [1] Nobody needs to install an app, because it runs in the phone browser. [1] The person who starts the session shares a link or QR code, and the crew joins from it. [1] The facts available do not say how the call copes with wind or engine noise, so test it on site before relying on it.
A phone video call app is a second option. No facts for it are available here, so check whether the call stays clear in wind, whether the crew can hear it over engine noise, and whether the phone locks its screen during the lift.
A two-way radio is a third option. No facts for it are available here, so check whether the crew already has radios, whether the channel stays clear during the lift, and whether radios are allowed on that site.
Match the option to the crew and the site, and keep a fallback ready in case the call drops during the shift.
Common mistakes to avoid
Relying on a single voice channel with no fallback, so that a dropped call leaves the crew with no way to send a command. Testing the phone sound indoors and assuming it will work over the engine and wind on the crane. A jobsite with nobody in it is wiped after 3 idle hours. [1] Sharing a link and forgetting that it stops working 12 hours after the first person joins it. [1] Expecting every phone to alert the same way, since iPhone Safari ignores the buzz that Android browsers give for signals such as STOP. [1] Letting a crew member talk over the phone without a set phrase for each command, so instructions get mixed up in the noise.
Frequently asked questions
Is OperatorLink free to use for offshore crane crews?
OperatorLink is currently free to use, and no paid plan is built yet. [1] Button presses, chat and voice pass between phones in a browser. [1]
Can OperatorLink voice calls be heard over wind and engine noise?
The facts available say that anyone who joins can take part in a voice call run from the phone browser. [1] They do not say how the call copes with wind or engine noise, so that is something to test on site with the full crew and the actual equipment before relying on it. Keep a hand signal or a radio as a fallback in case the call is hard to hear.
How long does an OperatorLink session link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] A session with nobody in it is wiped after 3 idle hours. [1] For a new shift, start a fresh session and share the new link or QR code with the crew, so everyone joins from a link that still works.
Do phones buzz when OperatorLink sends a signal?
On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1]
Can OperatorLink be added to a phone's home screen?
Yes, the app can be added to a phone's home screen as a standalone app. [1] It still runs in a phone browser, and there is no app install needed. [1]
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift