2Dig Plain comparisons of crane signalling and jobsite communication tools

Keep Rigging Crews on One Channel During Load-In

Learn how stage and event rigging crews can keep load-in signals in view, agree on one channel, and compare phone-based and radio options.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

To keep a stage and event rigging team on one channel during load-in, agree on who sends signals, how the crew acknowledges them, and what happens when STOP is called. Choose a shared communication method, confirm every crew member can receive it, and keep a backup method ready. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser. [1]Currently free to use, with no paid plan built yet. [1]not published
Two-way radionot publishednot publishednot published
Phone voice-call appnot publishednot publishednot published
Direct voice and agreed hand signalsnot publishednot publishednot published

What you need before you start

Before load-in begins, agree on how the rigging team will communicate during each lift and movement. Set out who gives directions, who acknowledges them, and what the crew does when a direction is unclear. Use plain words that everyone on the job understands, and make sure each person knows how to call STOP.

Choose a communication method that the crew can use throughout the work. If using phones, check that every phone has a working browser and data signal, because OperatorLink passes button presses, chat and voice between phones in a browser. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1]

Decide who will check that everyone has joined and can see the signals before work starts. For a phone-based setup, agree on how the crew will handle HOLD and SLOW, since both remain on for everyone until the last person leaves the jobsite. [1] Check how the chosen method behaves around loud equipment, moving loads, and areas where phone reception may change. Keep an agreed backup communication method available, and confirm that the crew knows when to stop work if a message is missed or misunderstood.

Step by step

  1. Agree on the channel before load-in. Choose the method the team will use to share directions. Make sure the people giving and receiving instructions know how to use it and which person is responsible for each direction.
  1. Set plain call words. Agree on the meaning of STOP, HOLD and SLOW, along with short acknowledgments for routine calls. OperatorLink sends one-tap radio-style calls such as Go Ahead, Copy That and All Clear as chat messages. [1] Agree on how the crew will confirm a message when voice or chat is not enough.
  1. Open the shared communication session. If using OperatorLink, the person starting the jobsite opens it in a phone browser, without installing an app. [1] That person shares the link or QR code so each crew member can join. [1]
  1. Check the crew before moving anything. Confirm that everyone who needs the signals has joined and can see the shared status. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] Do not assume that sharing a link means every person has successfully joined.
  1. Agree on how to handle each signal. With OperatorLink, HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1] A held move button keeps sending that move to the other phones, and if it stops arriving for 2 seconds, those phones drop it. [1] Make sure the crew understands these behaviors before work starts.
  1. Check the STOP response. OperatorLink's STOP signal releases every held direction on every phone and shows a full-screen alert to everyone else. [1] Agree that a STOP call means work pauses while the crew checks the situation and confirms it is safe to proceed.
  1. Keep communication available throughout the lift. Anyone who joins an OperatorLink jobsite can take part in a voice call run from the phone browser. [1] Watch for missed messages, unclear acknowledgments, or changing reception. If the team cannot confirm a direction, stop and use the agreed backup method.
  1. Close out the session. Have the crew leave when the jobsite communication session is no longer needed. An OperatorLink jobsite with nobody in it is wiped after 3 idle hours, and its link stops working 12 hours after the first person joins. [1] [1] Start a fresh session for later work when needed.

Tools that can do it

OperatorLink

OperatorLink is made by the team that publishes this site, 2Dig. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] The crew can join from a link or QR code, without installing an app. [1] Anyone who joins can take part in a voice call, and quick calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] [1] OperatorLink is currently free to use, and no paid plan is built yet. [1] Phone-based communication depends on having a working data signal. Check whether the crew's phones can stay connected where the rigging work will take place.

Two-way radio

A two-way radio is another option to consider for coordinating crew calls. Before choosing one, check whether the available radios cover the working area, whether the crew can hear calls over equipment noise, and how everyone will acknowledge instructions. Agree on the channel and the words used for STOP before load-in starts.

Phone voice-call app

A phone voice-call app is another option for keeping crew members talking during load-in. Check whether everyone can join the same call, whether speech remains clear in the working environment, and how the crew will handle a dropped call or missed instruction. Confirm that the chosen app supports the way the team needs to communicate before relying on it.

Direct voice and agreed hand signals

Direct voice and agreed hand signals can be considered as part of the crew's communication arrangements. Decide when they will be used, how the crew will make sure a signal is understood, and what happens when the person giving a direction is not visible or cannot be heard.

Compare each option against the work area, noise, phone reception, and the crew's agreed procedures. Keep a backup method ready, and do not continue a movement when the team cannot confirm the instruction.

Common mistakes to avoid

Starting load-in before everyone agrees on the channel can leave crew members unsure where instructions will arrive. Confirm the chosen method, call words, acknowledgments, and STOP procedure before work begins.

Assuming that a shared phone session means every person is receiving signals can leave gaps in communication. With OperatorLink, confirm that each crew member has joined and can see the shared signals. [1] The signals pass between phones in a browser, so check that the phones have a working data signal. [1]

Treating HOLD and SLOW as momentary signals is another mistake to avoid when using OperatorLink. Both stay on for everyone in the jobsite until the last person leaves. [1] Make sure the crew knows how that behavior affects its agreed procedure.

Assuming that STOP produces the same phone alert on every device can lead to missed warnings. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] Check the alert on the phones the crew will use.

Leaving an empty OperatorLink jobsite open for a later shift can also cause confusion. An empty jobsite is wiped after 3 idle hours, and the link stops working 12 hours after the first person joins. [1] [1] Start a new session when needed, and share its link or QR code with the crew. [1] Finally, never assume that a call was understood simply because it was sent. If an acknowledgment is missing or a direction is unclear, pause and confirm it using the agreed communication method.

Things to check before you choose

Before choosing a method for stage and event rigging load-in, check whether every crew member can access it in the actual work area. For phone-based communication, confirm data reception, browser access, and the way alerts appear on the phones being used.

Check how the method handles urgent calls, acknowledgments, and unclear instructions. If using OperatorLink, make sure the team understands how STOP releases held directions and how HOLD and SLOW remain active until the last person leaves. [1] [1]

Also check the session timing before planning a long load-in. OperatorLink links stop working 12 hours after the first person joins, and empty jobsites are wiped after 3 idle hours. [1] [1] Decide who will start a new session if the work requires one. Keep the crew's established safety procedures and backup communication arrangements in place.

Frequently asked questions

How can rigging crews keep everyone on one channel during load-in?

Agree on a shared communication method before work begins, identify who gives directions, and establish plain call words and acknowledgments. Confirm that everyone can receive the calls and understands what to do if a message is unclear. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] Keep a backup communication method available.

Can OperatorLink be used for stage and event rigging?

OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] The person starting a jobsite shares a link or QR code, and the crew joins from it. [1] Check that the phones have working data reception in the work area and that the crew understands how to respond to each signal before starting.

Does OperatorLink require a phone app installation?

OperatorLink runs in a phone browser and does not require an app installation. [1] The page can also be added to a phone's home screen as a standalone app. [1] Before load-in, check that each phone can open the page and has a working data signal. Confirm that every crew member has joined the correct jobsite session.

What happens when STOP is pressed in OperatorLink?

STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] The crew should agree in advance that STOP means the movement pauses while the situation is checked. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] Check how the alert appears on each phone.

How long does an OperatorLink jobsite stay available?

An OperatorLink jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a later shift, check whether the existing link is still valid. Start a new jobsite and share its link or QR code if a fresh session is needed. [1]

Can the rigging crew talk through OperatorLink?

Anyone who joins an OperatorLink jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Phone-based communication depends on a working data signal, so check reception in the work area and keep an agreed backup method available.

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons