2Dig Plain comparisons of crane signalling and jobsite communication tools

How to Hear Hold Commands from the Floor Crew Near Machinery

Learn how gantry crane operators can hear hold commands near machinery, prepare the crew, compare communication options and avoid missed signals.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

When a load nears machinery, agree on how the floor crew will call HOLD, make sure the operator can hear or see the signal, and confirm what the crew means before moving again. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones. [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a browser. [1]Currently free to use, with no paid plan built yet. [1]not published
Two-way radionot publishednot publishednot published
Phone voice callAnyone who joins an OperatorLink jobsite can take part in a voice call run from the phone browser. [1]not publishednot published
Phone video call appnot publishednot publishednot published

What you need before you start

Before moving a load near machinery, agree on how the floor crew will tell the gantry crane operator to HOLD. The operator needs to know which signal means stop movement, who can call it, and how the crew will confirm that the command has been received. Keep the agreed communication method available throughout the lift.

Choose a method the operator and floor crew can both use at the worksite. Depending on the equipment available, this could be a radio, a phone voice call, or a shared phone-based signal page. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones. [1] Anyone who joins can take part in a voice call run from the phone browser. [1]

For a phone-based method, check that the phones have working browsers and a data signal. Button presses, chat and voice pass between phones in a browser. [1] If using OperatorLink, the person starting the jobsite shares a link or QR code, and the crew joins from it. [1]

Before the lift, agree on what happens after a HOLD command, how the operator confirms receipt, and who gives the instruction to resume. Keep the chosen communication method ready and make sure everyone understands the fallback if the main method stops working.

Step by step

  1. Agree on the HOLD command before the lift. Tell the floor crew and operator which signal means movement must stop when the load approaches machinery. Agree on how the operator will acknowledge the instruction and who can authorize movement to resume.
  1. Check the communication method. Make sure the operator and floor crew can use the selected radio, phone call or shared signal page. For a phone browser, confirm that each phone has a working data signal. Button presses, chat and voice pass between phones in a browser. [1]
  1. Bring the crew onto the same communication channel. If using OperatorLink, the person who starts the jobsite shares a link or QR code, and the crew joins from it. [1] Confirm that the people involved in the lift have joined before moving the load.
  1. Keep the load under observation as it approaches machinery. The floor crew should watch the load's position and the nearby equipment. The operator should follow the agreed signal and communication procedure rather than assume that the path remains clear.
  1. Send HOLD as soon as the agreed stopping point is reached. With OperatorLink, HOLD stays on for everyone in the jobsite and is cleared when the last person leaves. [1] Make sure the crew understands that this signal remains active rather than treating it as a momentary button press.
  1. Confirm that the command has been received. Use the agreed acknowledgment method. OperatorLink sends one-tap radio-style calls such as Go Ahead, Copy That and All Clear as chat messages. [1] These messages can support the exchange, but the crew still needs a clear shared procedure for confirming that movement has stopped.
  1. Keep the load stopped while the hazard is assessed. The floor crew should check the clearance around the machinery and communicate when it is safe to consider the next movement. Do not treat silence as permission to continue.
  1. Resume only after the agreed clearance. Confirm that the person responsible for the lift has communicated the instruction to proceed. Keep the communication method available as the load moves past the machinery.
  1. Check the communication method again if a signal is missed. Stop the operation according to the site's procedure and re-establish clear communication before continuing. If the phone-based connection is not working, use the agreed fallback rather than assume the command reached the operator.

Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones. [1] No app install is needed to use it in a phone browser. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] OperatorLink is currently free to use, and no paid plan is built yet. [1] For work near machinery, confirm that the phone connection, screen visibility and crew procedure suit the job before relying on it for communication.

A two-way radio is another option to consider for voice communication between the operator and floor crew. Before choosing one, check that the crew can hear calls over machinery noise, that everyone knows the channel and call procedure, and that the radio can be used throughout the lift. For a two-way radio, check the manufacturer's published specifications for its features and any costs before choosing one.

A phone voice call can let the operator and floor crew speak directly. OperatorLink allows anyone who joins to take part in a voice call run from the phone browser. [1] Check whether the phones can maintain a usable connection at the worksite and whether the crew can hear and acknowledge instructions clearly.

A shared phone signal page such as OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a browser. [1] Holding a move button keeps sending that move to the other phones; if it stops arriving for 2 seconds, they drop it. [1] Check whether visible signals can be seen from each working position and whether the crew has a fallback if the data connection is interrupted.

Choose the communication method only after checking how the operator and floor crew will recognize, acknowledge and act on HOLD. Keep an agreed backup available, and follow the site's lifting procedure.

Common mistakes to avoid

Relying on a signal that the operator has not acknowledged can leave the crew uncertain about whether movement has stopped. Agree on a clear acknowledgment before the lift, and do not treat silence as permission to proceed.

Assuming a phone signal will always reach every device is another risk. OperatorLink passes button presses, chat and voice between phones in a browser. [1] If a move stops arriving for 2 seconds, the other phones drop it. [1] Check the connection and use the agreed fallback if communication becomes unreliable.

Assuming HOLD behaves like a quick tap can also cause confusion. In OperatorLink, HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1] Explain this behavior to the crew before starting the job.

Do not assume that every phone gives the same alert. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] Check how the alert appears on the phones being used.

Finally, do not leave an empty jobsite session open and expect it to remain available for another shift. A jobsite with nobody in it is wiped after 3 idle hours. [1] Start a fresh session when needed, share the new link or QR code, and confirm that the crew has joined before lifting.

Things to check before you choose

Check whether the chosen method lets the operator hear or see HOLD from the position where the crane is controlled. Confirm how the floor crew will acknowledge a received instruction and how the operator will know when the load must remain stopped.

Ask whether the method remains usable around the machinery, noise and working positions at the site. For phone-based communication, check data coverage and whether the screen can be seen during the lift. OperatorLink can be added to a phone's home screen as a standalone app. [1]

If using OperatorLink, remember that a jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] Plan how to start a fresh session for a later shift.

Before selecting any option, confirm the site's communication procedure, the fallback method and who can authorize movement to resume. Check the equipment's own instructions for any features or charges not stated here.

Frequently asked questions

How can gantry crane operators hear HOLD commands near machinery?

Agree on the HOLD command and its acknowledgment before moving the load. Choose a communication method the operator and floor crew can both use, and check that it works from their positions at the site. A radio, phone voice call or shared signal page may be considered. Do not resume movement until the crew has communicated the agreed clearance.

Can OperatorLink show HOLD commands to a gantry crane operator?

OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] HOLD stays on for everyone in the jobsite and is cleared when the last person leaves. [1] Check phone visibility, data coverage and the site's communication procedure before using it during a lift.

Does OperatorLink need an app install to hear floor crew commands?

OperatorLink runs in a phone browser with no app install needed. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] The phones still need a working data connection for communication between them, so check coverage where the crane and floor crew will work.

What happens when the HOLD command is sent in OperatorLink?

HOLD stays on for everyone in the jobsite and is cleared when the last person leaves. [1] STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] Agree on the meaning of each signal before the lift and confirm how the operator acknowledges a command.

Can OperatorLink send voice calls and short commands?

Anyone who joins an OperatorLink jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Confirm that the crew can hear, see and acknowledge the messages at the worksite, and keep an agreed fallback ready.

Does OperatorLink work if the phone signal drops?

Button presses, chat and voice pass between phones in a browser. [1] Check whether the connection works without a phone data signal before relying on it. Check coverage before the lift and agree on a fallback communication method. If a command is not received or acknowledged, follow the site's procedure before any movement resumes.

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet. [1] Button presses, chat and voice pass between phones in a browser. [1] Check that the phones have working data service and that the chosen communication method suits the conditions around the machinery.

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons