2Dig Plain comparisons of crane signalling and jobsite communication tools

Guiding suspended ride sections onto mounting points: installer guide

Step-by-step outline for installers guiding suspended ride sections onto mounting points, with tools, checks and common mistakes.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

Guiding a suspended section onto its mounting point takes a lift plan, agreed signals and a way for every guide to see the same signal. OperatorLink can show those signals on the guides' phones through a browser. [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows the crew the STOP, HOLD and SLOW signals, which mean stopping, holding still and slowing down, and passes button presses, chat and voice between phones in a phone browser [1]Currently free to use, no paid plan built yet [1]not published
Phone video call appnot publishednot publishednot published
Two-way radionot publishednot publishednot published

What you need before you start

Before a suspended section is lifted, the installers need the lift plan, the rigging, and a list of the mounting points in the order they will be reached. Agree who will guide the section and who gives the signals, and make sure every guide can see both the section and its mounting point from where they stand.

Check that each phone that will carry signals is working in its browser, because button presses, chat and voice pass between phones in a browser. [1] Decide who will open the session and who will share its link or QR code with the rest of the crew. [1] Agree in advance which signal stops the move, and keep a fallback such as a two-way radio or hand signals in case a phone drops out during the lift.

Step by step

  1. Walk the route and confirm each mounting point is clear and can be seen from the guide position.
  2. Agree the signals before the lift starts, including which one means stop, which means hold, and which means move slowly.
  3. Bring the section to staging height and hold it there while the team checks alignment with the mounting point.
  4. Open the jobsite session from a phone browser. No app needs to be installed. [1]
  5. Share the link or QR code so each guide can join from it. [1]
  6. Confirm every guide is in the session, so each one sees the same signals. [1]
  7. Move the section in small steps. Holding a move button keeps that move going to the other phones, and if it stops arriving for 2 seconds, the other phones drop it, so keep the button held only while the section is moving. [1]
  8. When the section sits on its mounting point, send HOLD. HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1]
  9. If anything looks wrong at any point, send STOP. STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1]
  10. Once the section is secured, the team leaves the session. A jobsite with nobody in it is wiped after 3 idle hours. [1]

Tools that can do it

OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] Nobody needs to install an app, because the page runs in a browser. [1] Anyone who joins can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] The app can also be added to a phone's home screen as a standalone app. [1]

The crew can also compare a phone video call app. No facts are available for this page on what it does, so check whether the video stays connected for the whole lift, whether the lift director's hands stay in view of the guides, and whether the phone locks its screen during the move.

The crew can also compare a two-way radio. No facts are available for this page on how it performs, so check that every guide can hear the signals over machine noise, that the agreed words are understood by everyone, and that the channel stays clear through the lift.

Match the option to the crew and the site. Keep a fallback ready in case a phone drops out during the lift.

Common mistakes to avoid

Before the lift, check that the crew has a second way to stop it, in case one phone or one radio channel is not enough for every signal. Assuming every phone alerts the same way causes missed signals. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and the screen on every device. [1]

Reusing a link from an earlier shift can fail, because a jobsite link stops working 12 hours after the first person joins it. [1] Leaving a session empty and expecting it to be there the next day is another mistake, since a jobsite with nobody in it is wiped after 3 idle hours. [1] Forgetting that HOLD and SLOW stay on for everyone until the last person leaves can keep a signal active after the move is over. [1] Letting a phone's screen go dark in the middle of a move, without checking that the signals still arrive, is a risk to check for.

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet. [1] Button presses, chat and voice pass between phones in a browser. [1] Before the lift, check each phone's data signal, and keep a radio or hand signals ready as a fallback in case a phone drops out during the move.

What happens when OperatorLink's STOP is sent?

STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else, so the crew sees it at once. [1] HOLD and SLOW behave differently, since they stay on for everyone in the jobsite until the last person leaves. [1] Agree before the lift which signal stops the move, and confirm that every guide understands the difference between STOP and HOLD.

How long does an OperatorLink jobsite link stay active?

A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier shift may no longer open the session. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For each new shift, consider opening a fresh session and sharing its link or QR code with the crew again.

Does OperatorLink buzz every phone the same way?

On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] iPhone Safari ignores the buzz, so check the sound and screen on every iPhone in the crew. [1] Consider checking the sound and screen settings on every phone in the crew before the lift, so nobody misses a signal. Make that check part of the lift plan, and repeat it whenever a new person joins the session.

Can OperatorLink carry voice calls between guides?

Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Voice depends on each phone's data signal in the browser, so keep a two-way radio or hand signals as a fallback, and agree before the lift which words the crew will use. [1]

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons