How to guide rooftop unit placements with the crane operator
Steps for HVAC lift crews guiding rooftop unit placements with the crane operator from the roof edge, with what to have ready and common mistakes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
For a rooftop unit placement, the signal person at the roof edge and the crane operator can each use a phone to see the same STOP, HOLD and SLOW signals, with a voice or hand fallback in place. [1] The signals run in a phone browser, so each phone needs a working data signal for the shift. [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, and no paid plan is built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Rooftop unit placements depend on one signal person at the roof edge, who can see the unit and the landing spot, and on a crane operator who may not see that spot from the ground. Before the lift, the crew should agree who stands at the roof edge, who works with the crane operator, and which signals each person uses.
Every crew member needs a phone with a working browser, because the signals pass between phones in a browser. [1] The person who starts the session shares a link or QR code, and the rest of the crew joins from it. [1] A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier day may not open. [1] Decide which signals stay on for the whole placement, since HOLD and SLOW stay on for everyone until the last person leaves. [1]
Step by step
- Walk the roof with the crew and mark the landing spot and the roof edge where the signal person will stand, before the lift starts.
- Check that each phone has a working browser for the session. [1]
- The person who starts the session opens it from a phone browser, with no app install needed. [1]
- That person shares the link or QR code, and each crew member joins from it. [1]
- Confirm everyone, including the roof edge signal person and the crane operator, is in the session before the first move. [1]
- Agree on the signals in use. STOP, HOLD and SLOW are shown to the whole crew. [1]
- Use HOLD or SLOW while the unit is positioned, since they stay on until the last person leaves. [1]
- The roof edge signal person sends each move with a press-and-hold button, and the move keeps going to the other phones while the button is held. [1] If a move stops arriving for 2 seconds, the other phones drop it. [1]
- Confirm each step with a one-tap call such as Go Ahead, Copy That or All Clear, which is sent as a chat message. [1]
- If anyone sees a hazard, press STOP. It releases every held direction on every phone and shows a full-screen alert to everyone else, so the crew pauses and looks before moving again. [1]
- Keep a voice or hand fallback ready in case a phone loses its signal during the placement.
- At the end of the shift, everyone leaves the session. A session with nobody in it is wiped after 3 idle hours. [1]
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody installs an app, because the page runs in a browser. [1] Anyone who joins can take part in a voice call run from the phone browser. [1] On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so the crew should check the sound and screen on each phone. [1] The page can also be added to a phone's home screen for quick access. [1]
A phone video call app is a second option. No facts here describe one, so check whether the call stays open for the whole placement, whether the roof edge signal person can be seen from the crane, and whether the phone locks its screen during the lift.
A two-way radio is another option. No facts here describe one, so check that every crew member can hear the calls over machine noise, that the crew agrees on plain voice terms, and that the channel stays clear through the lift.
Match the option to the crew and the site, and keep a fallback ready, since signals in a browser depend on a working data signal. [1]
Common mistakes to avoid
Relying on one phone for every signal. Give the crew a voice or hand fallback in case a phone loses signal.
Assuming every phone alerts the same way. On Android browsers signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device. [1]
Leaving the session open over a break and expecting it to hold. A session with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on for everyone until the last person leaves, so the signals remain active until the session is empty. [1]
Assuming a move keeps running after the button is let go. If a move stops arriving for 2 seconds, the other phones drop it. [1]
Using a link from an earlier day. A jobsite link stops working 12 hours after the first person joins it. [1]
Treating the phones as the whole signal plan. Keep the signal person at the roof edge and the agreed hand signals in place alongside the session.
Frequently asked questions
Is OperatorLink free to use?
OperatorLink is currently free to use, and no paid plan is built yet. [1] The signals run in a phone browser, so each phone still needs a working data signal for the shift. [1] Check the data plan on every phone before the crew relies on it, and keep a voice or hand fallback in case a phone loses signal during the placement.
What happens when STOP is pressed in OperatorLink?
STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, since they stay on for everyone until the last person leaves the jobsite. [1] After a STOP, the crew should pause and look before moving again, and agree on which signal is active before the next move.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, start a new session and share the new link or QR code with the crew, so every member joins the current session. [1]
Do STOP signals buzz every phone in OperatorLink?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone the alert may only be seen on screen. [1] Check the sound and screen settings on every phone in the crew before the lift.
Can the crew talk by voice in OperatorLink during a lift?
Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Voice depends on each phone's working data signal, so keep a radio or hand signal as a fallback for the placement. [1]
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift