How to guide precast panels into place with the operator
Steps for precast concrete installers to guide panels into place with the operator, with notes on the signals, phone sessions and common mistakes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Guiding a precast panel into place goes well when the crew agrees on the signals before the lift and one guide can see both the panel and the operator. OperatorLink is one option among several, and it shows STOP, HOLD and SLOW to the crew in a phone browser. [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Guiding a precast panel into place depends on one guide on the ground who can see both the panel and the crane operator. Before the lift, decide who is the guide, who handles the panel, and who watches the landing point. Agree on the words for STOP, HOLD and SLOW so everyone reads the same signal. Check that every phone or radio is charged and that each person knows how to use it, because a signal only helps if it arrives.
If the crew uses phones, each phone needs a working browser and a data signal for the whole shift, since button presses and chat pass between phones in a browser. [1] The person who starts the session shares a link or QR code with the rest of the crew. [1] Add the page to the phone's home screen before the lift so it opens as a standalone app. [1]
Step by step
- Walk the panel's path and agree on the landing point, so the guide and the operator work from the same picture.
- The person who starts the session opens it from a phone browser, with no app install needed. [1]
- Everyone else joins from the shared link or QR code. [1]
- Confirm every crew member is in the session before the panel leaves the ground, so each one sees the same signals. [1]
- Agree on which signals stay on. HOLD and SLOW stay on for everyone in the jobsite until the last person leaves, so the crew should know they are still active. [1]
- Lift slowly and let the guide call each move. Holding a move button keeps that move sent to the other phones. If it stops arriving for 2 seconds, the other phones drop it, so the guide keeps watching the screen. [1]
- Use one-tap calls such as Go Ahead, Copy That and All Clear for short confirmations, which are sent as chat messages. [1]
- If anything looks wrong, the guide presses STOP. It releases every held direction on every phone and shows a full-screen alert to everyone else, so the operator pauses before moving again. [1]
- Once the panel is set and secured, the crew stops the moves and everyone leaves the session. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Anyone who joins can take part in a voice call run from the phone browser, so the guide and the operator can talk during the lift. [1] For short confirmations, one-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] OperatorLink is currently free to use, and no paid plan is built yet. [1]
A phone video call app is a second option. This page has no published details on it, so check whether the call can stay open for the whole shift, whether the guide can keep the operator in view on screen, and whether the phone locks its screen during the lift.
A two-way radio is a third option. This page has no published details on it, so check that every crew member can hear the guide over machine noise and that the channel stays clear through the lift.
Match the option to the crew and the site, and keep a fallback ready, since the browser signal depends on the phone's data signal. [1]
Common mistakes to avoid
Relying on one phone for STOP. Button presses pass between phones in a browser, so keep a voice or hand signal ready in case a phone loses its data signal. [1]
Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so check the screen and sound on every iPhone before the lift. [1]
Using a link past its life. A jobsite link stops working 12 hours after the first person joins it, so share a fresh link or QR code for each shift. [1] [1]
Expecting an empty session to wait for the next shift. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on until the last person leaves. [1]
Not watching a held move. Other phones drop a move that stops arriving for 2 seconds. [1]
Letting the phone sleep during the lift. Add the page to the home screen before the lift, and check the screen timeout settings on each phone. [1]
Frequently asked questions
Is OperatorLink free to use for precast crews?
OperatorLink is currently free to use, and no paid plan is built yet. [1] The crew still needs a phone with a working browser and a data signal, since button presses and chat pass between phones in a browser. [1] Check the phone's data plan for the whole shift before relying on it, and keep a voice or hand signal ready as a fallback in case the signal drops.
What happens when someone presses STOP in OperatorLink?
STOP releases every held direction on every phone in the jobsite and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, because they stay on for everyone until the last person leaves the jobsite. [1] After a STOP, the guide should confirm the panel is safe to move before the crew resumes the lift.
How long does an OperatorLink jobsite link last?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For each new shift, start a fresh session and share the new link or QR code with the crew, so nobody joins from an old link. [1]
Do STOP signals buzz on every phone in OperatorLink?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone the alert depends on the screen being seen. [1] Check the sound and screen on every phone before the lift so nobody misses a signal, and place each iPhone where the guide and the operator can see it clearly.
Can the crew talk by voice during a panel lift with OperatorLink?
Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages, which suits short confirmations during the lift. [1] Voice runs through the phone browser, so keep a radio or hand signal as a fallback in case a phone loses its signal. [1]
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift