2Dig Plain comparisons of crane signalling and jobsite communication tools

How to guide machines around ground crews

Steps for heavy equipment spotters to guide machines around ground crews, with what to set up, a comparison of signal tools and common mistakes.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

A spotter stays where the operator can see both the spotter and the machine's path, agrees on the signals with the crew before any move, and treats a stop signal from anyone on the crew as a reason to pause. Phones, radios and hand signals can each carry those signals, so choose the tool that suits the crew and the site.

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1]Currently free to use, no paid plan built yet [1]not published
Phone video call appnot publishednot publishednot published
Two-way radionot publishednot publishednot published

What you need before you start

A spotter is the person on the ground who guides the machine operator, so the spotter has to stay where the operator can see both the spotter and the path of the machine. Before any move, agree on the signals with the operator and the crew, and make sure everyone knows which signal means stop. Clear the path of people and loose gear, and confirm who will be working inside the reach of the load. A spotter who is not sure the operator can see them should not give a move.

Check the tools the crew will use before the shift starts. Each phone that carries signals needs a working browser and a data signal, and a radio needs charged batteries and an agreed channel. Decide ahead of time who watches for each signal, and keep a voice or hand signal ready as a backup in case a phone connection drops.

Step by step

  1. Walk the route with the operator and the crew before the machine moves, and mark where people will be working near the load.
  2. Agree on the signals in plain words: which signal means stop, which means hold, and which means slow. Make sure the operator knows each one.
  3. Stand where the operator can see you and the machine's path, and keep clear of the swing and the load.
  4. Give one signal at a time, and wait for the operator to acknowledge it before the machine moves.
  5. If phones are part of the signalling, the person who starts the jobsite shares a link or QR code, and the crew joins from it. [1] Confirm every crew member is in the session before the lift begins. [1]
  6. Holding a move button keeps sending that move to the other phones, and if it stops arriving for 2 seconds, the other phones drop it, so keep the button held while the move is in progress. [1]
  7. When a stop is called, the operator halts the machine and the crew pauses before moving again. On the phones, STOP releases every held direction and shows a full-screen alert to everyone else. [1]
  8. At the end of the shift, everyone leaves the session. A jobsite with nobody in it is wiped after 3 idle hours. [1]

Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody needs to install an app, because the page runs in a browser. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1]

A phone video call app is a second option. When you set up a phone video call, confirm that the crew can keep the call open for the whole shift, that the spotter stays in view of the operator, and that the phone does not lock its screen during the lift.

A two-way radio is a third option. Check that the crew agrees on plain spoken words, that every member can hear over machine noise, and that the channel stays clear through the lift.

Match the option to the crew and the site, and keep a fallback ready, since a phone connection can drop in the middle of a lift.

Common mistakes to avoid

Giving a move before the operator has seen the signal. Wait for the operator to acknowledge each signal before the machine moves.

Relying on one phone for STOP. A phone connection can drop, and then the rest of the crew may not see the stop, so keep a voice or hand signal ready at all times.

Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device. [1]

Forgetting that HOLD and SLOW stay on until the last person leaves the jobsite, so a crew that forgets them may keep working under an old signal. [1]

Reusing an old link or session. A jobsite link stops working 12 hours after the first person joins it, and a jobsite with nobody in it is wiped after 3 idle hours. [1] [1]

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet. [1] Because it runs in a phone browser with no app install, the phone still needs a working data signal for the whole shift. [1] Check the phone's data plan with the crew before relying on it, since a dropped signal can interrupt the signals sent between phones.

What happens when STOP is pressed in OperatorLink?

STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, since they stay on for everyone until the last person leaves the jobsite. [1] A spotter should still call a stop by voice or hand when the crew is close to the machine, because a phone may not be in hand at the moment it is needed.

How long does an OperatorLink jobsite link stay active?

A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, start a new session and share the new link or QR code with the crew, so no one joins an old session by mistake. [1]

Do STOP signals buzz on every phone in OperatorLink?

Not on every phone. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] An iPhone in the crew may therefore show the alert on screen only, so check the sound and screen settings on every phone before the lift begins.

Can OperatorLink be used for voice calls during a lift?

Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] A dropped phone signal can stop a voice call, so keep a radio or hand signal ready as a fallback for the whole shift.

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons