2Dig Plain comparisons of crane signalling and jobsite communication tools

How to guide machinery lifts into elevator shafts

Steps for elevator installers guiding machinery lifts into elevator shafts, the tools that can help, and mistakes to avoid on the job.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

To guide a machinery lift into an elevator shaft, agree on one person to give the signals, set the signal method before the load moves, and confirm the whole crew can see each signal. OperatorLink is one option: it shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser. [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1]Currently free to use, no paid plan built yet [1]not published
Phone video call appnot publishednot publishednot published
Two-way radionot publishednot publishednot published
Hand signals from one signal personnot publishednot publishednot published

What you need before you start

Before a machinery lift starts moving toward an elevator shaft, the installers on the job need a clear way to tell each other when to stop, hold or slow down. Decide first who gives the signals and who acts on them, and make sure everyone on the crew can see or hear that person from where they stand.

Button presses, chat and voice pass between phones in a browser. [1] One person starts the shared session and shares a link or QR code, and the rest of the crew joins from it. [1] Agree before the lift who will keep the phone that shows HOLD and SLOW in view, since those two signals stay on for everyone until the last person leaves the session. [1] A link stops working 12 hours after the first person joins, so a link from an earlier day may not open the session. [1] Before the lift, the page can be added to a phone's home screen, where it opens as a standalone app. [1] Check that each phone's sound and screen are set so an alert will be noticed, and keep a spoken or hand signal ready as well.

Step by step

Work through these steps in order, with one signal person and the crew agreed before the load moves.

  1. Walk the route of the machinery lift and the shaft opening with the crew before anything moves, so everyone knows where the load will travel and where each person will stand.
  2. Name one person to give all signals and a second person to take over if the first cannot be seen from the lift.
  3. Open the session from a phone browser. It runs in the browser with no app install. [1]
  4. Share the link or QR code with the crew, and have each member join from it. [1]
  5. It shows STOP, HOLD and SLOW to the jobsite crew, and passes button presses, chat and voice between phones in a phone browser. [1]
  6. When STOP is sent, every held direction is released on every phone and everyone else sees a full-screen alert, so agree in advance who sends it. [1]
  7. Use HOLD and SLOW for conditions that last, since both stay on for everyone until the last person leaves the session. [1]
  8. Keep move buttons held only while a move is needed. A held move keeps going to the other phones, and if it stops arriving for 2 seconds, they drop it. [1]
  9. Use one-tap calls such as Go Ahead, Copy That and All Clear for short replies, which are sent as chat messages. [1]
  10. Open a voice call when a longer exchange is needed, since anyone who joins the session can take part. [1]
  11. When the lift is finished, have everyone leave the session. A session with nobody in it is wiped after 3 idle hours. [1]

Tools that can do it

It shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody needs to install an app, because it runs in the browser. [1]

A phone video call app is a second option. No facts here describe one, so check whether the call can stay open for the whole lift, whether the person giving signals stays in view of the screen, and whether the phone's screen stays on during the move.

A two-way radio is a third option. No facts here describe one, so check that every crew member can hear the signals over the noise on site, that the channel stays clear during the lift, and that everyone agrees on the words used for each signal.

Hand signals from one signal person are a fourth option. Check that the person giving the signals can be seen from every position where the crew stands.

Match the option to the crew and the lift, and keep a fallback ready.

Common mistakes to avoid

Relying on one phone for STOP. Button presses, chat and voice pass between phones in a browser. [1]

Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check sound and screen on every device. [1]

Reusing an old link. A link stops working 12 hours after the first person joins it, so a link from an earlier shift may not open. [1]

Leaving an empty session and expecting it to be there the next day. A session with nobody in it is wiped after 3 idle hours. [1]

Forgetting that HOLD and SLOW stay on. Both signals stay on for everyone until the last person leaves, so plan around them rather than assuming they clear on their own during the lift. [1]

Letting a move button run without checking the load. A held move keeps arriving on the other phones, and if it stops arriving for 2 seconds, they drop it, so watch the load for as long as a button is held. [1]

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet. [1] Button presses, chat and voice pass between phones in a browser. [1] Before the lift, check how the crew will notice signals and agree on a spoken or hand signal to use as a fallback.

What happens when STOP is sent in OperatorLink?

STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else, so the crew sees it on screen. [1] HOLD and SLOW behave differently, because they stay on for everyone until the last person leaves the session. [1] Everyone on the crew should know which signal does what before the load moves.

How long does an OperatorLink session link stay active?

A session link stops working 12 hours after the first person joins it, so a link from an earlier shift may no longer open the session. [1] A session with nobody in it is wiped after 3 idle hours. [1] For a new shift, the person who starts the session can share a new link or QR code with the crew. [1]

Does OperatorLink make phones buzz on every device?

On Android browsers, signals such as STOP make the phone buzz. [1] STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] Check the sound and screen settings on every phone in the crew before the lift, so nobody misses a signal.

Can OperatorLink carry voice calls between elevator installers?

Anyone who joins the session can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Button presses, chat and voice pass between phones in a browser. [1]

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons