How to coordinate tank shell plate lifts for erection crews
Steps, a checklist and tool options for coordinating tank shell plate lifts with a tank erection crew, including a phone browser option for crane signals.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Name one lift director and one signal person, agree on the signal list, and test every signal with the whole crew before the first plate moves. A phone browser option and two other options are covered below, with what to check for each.
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, and no paid plan is built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Before the first plate moves, the lift needs a named lift director, one signal person who gives the signals, and a written list of the signals the crew will use, such as STOP, HOLD and SLOW, with what each one means. Each crew member should know who is in the signal path and which parts of the shell course and the landing point the signal person can and cannot see. Agree on a backup for the moments when the signal person is out of sight, such as a second person who repeats each signal.
If the crew passes signals between phones, check each phone's browser and data connection before the shift starts. OperatorLink runs in a phone browser with no app install. [1] [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1]
Step by step
- Name the lift director and one signal person, and write down who gives each signal.
- Agree on the signal list, including STOP, HOLD and SLOW, and what the crew does when each one is given.
- Walk the route the plate will take and mark each spot where the signal person cannot be seen from the crane or the landing point.
- Confirm every crew member can see and hear each signal from where they will stand.
- If the crew uses OperatorLink, the person who starts a jobsite shares a link or QR code, and the crew joins from it. [1]
- Test every signal with the whole crew before the first plate is lifted, and confirm each phone shows the signal. [1]
- Agree on how HOLD and SLOW are cleared. HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1]
- When STOP is given, every crew member stops and looks before any movement starts again. In OperatorLink, STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1]
- At the end of the shift, the crew leaves the session, and the lift director confirms nobody is still holding a move.
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes the move buttons, texts and voice calls between phones through a browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Anyone who joins can take part in a voice call run from the phone browser. [1] OperatorLink is currently free to use, and no paid plan is built yet. [1]
A phone video call app is another option. This page publishes no facts about any particular video call app.
A two-way radio is a third option. This page has no published facts about any particular radio, so check that the crew agrees on plain voice calls, that every member can be heard over the machine noise on the site, and that the channel stays clear through the whole lift.
Compare the options against the checks above, and choose the one the crew can use from start to finish of the lift. Keep a fallback ready, because signals in a phone browser depend on each phone's browser and data signal.
Common mistakes to avoid
Depending on one phone or one person for STOP. If that phone or that person is out of reach, the rest of the crew may not get the signal, so keep a voice or hand signal ready as well. Signals in OperatorLink pass between phones in a browser, so each phone's browser and data signal matter. [1]
Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and the screen on every device before the lift starts. [1]
Reusing an empty session from an earlier shift. A jobsite with nobody in it is wiped after 3 idle hours, so a session left sitting overnight will not be there the next morning. [1]
Forgetting that HOLD and SLOW stay on until the last person leaves the jobsite. The crew has to clear them on purpose, or a signal left on can carry into the next move. [1]
Letting go of a move button and assuming the move is still going. Holding a move button keeps sending that move to the other phones, and if it stops arriving for 2 seconds, the other phones drop it, so the crew should check the plate's position before continuing. [1]
Letting a phone sleep during the lift. Adding the page to the phone's home screen lets it open as a standalone app, which helps the crew reach the session quickly when it matters. [1]
Frequently asked questions
Is OperatorLink free to use?
OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser with no app install, so the crew opens the session from a browser on each phone. [1] Confirm each phone can open the session before the lift starts, and check that the phone's data plan covers a full shift.
What happens when STOP is pressed in OperatorLink?
STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, because they stay on for everyone until the last person leaves the jobsite. [1] On Android browsers, STOP also makes the phone buzz, while iPhone Safari ignores the buzz, so the crew should rely on the screen as well as the sound. [1]
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] Separately, a jobsite with nobody in it is wiped after 3 idle hours. [1] For each new shift, start a fresh session and share its new link or QR code with the crew, so nobody joins from an old link. Confirm the new session is open before the lift starts.
Can OperatorLink carry voice calls during a tank shell plate lift?
Anyone who joins the session can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Because button presses, chat and voice pass between phones in a browser, each phone's browser and data signal matter. [1] Keep a hand signal or radio as a fallback, and test the voice call with the whole crew before the first plate moves.
How does a held move button work in OperatorLink?
Holding a move button keeps sending that move to the other phones; if it stops arriving for 2 seconds, they drop it. [1] If the move stops arriving for 2 seconds, the other phones drop it. [1] Agree on this rule before the lift, so every signal person and crew member acts on the same understanding.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift