2Dig Plain comparisons of crane signalling and jobsite communication tools

How to coordinate mast lifts with the assist crane operator

Steps for tower crane assembly crews to coordinate mast section lifts with the assist crane operator, with a checklist and tool options.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

Coordinating mast section lifts with the assist crane operator comes down to agreeing on the signals, who gives them, and how every person hears them before the lift starts. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew, and passes button presses, chat and voice between phones in a phone browser. [1] The page has no published details about a phone video call app or a two-way radio, so check what each one does before choosing.

OptionWhat it doesCost
OperatorLinkShows STOP, HOLD and SLOW to the jobsite crew and passes the move buttons, texts and voice calls between phones through a browser [1]Currently free to use, no paid plan built yet [1]
Phone video call appnot publishednot published
Two-way radionot publishednot published

What you need before you start

Before the first mast section is lifted, the tower crane assembly crew and the assist crane operator need the lift plan in hand, a named signal person, and an agreed set of signals for stop, hold and slow. Everyone on the crew should know who gives each signal and who has the final say on a stop.

Button presses, chat and voice pass between phones in a browser. [1] If the crew uses OperatorLink, the person who starts the jobsite shares a link or QR code, and the crew joins from it. [1] A jobsite link stops working 12 hours after the first person joins, so a link from an earlier day may not open the session. [1]

Decide before the lift whether the assist crane operator will be in the session or will use a separate channel, and tell everyone which one it is.

Step by step

  1. Hold a short meeting before the lift and write down the order of moves in the lift plan, the load path, and the rule for who can call a stop.
  2. Name the signal person for the mast section and the signal person for the assist crane, and agree that only those named people give signals.
  3. Agree on the words the crew will use for stop, hold and slow, and confirm that everyone knows what each one means.
  4. If the crew uses phones, have the person who starts the session open the page from a phone browser, with no app install needed. [1]
  5. Share the link or QR code, and confirm that every crew member, including the assist crane operator if they are on a phone, has joined before the lift begins. [1]
  6. Run a short signal check in a safe position before the mast section is loaded, and confirm that every phone shows the same signal.
  7. During the lift, the signal person gives each move. Holding a move button keeps sending that move to the other phones, and the other phones drop a move that stops arriving for 2 seconds, so confirm each move still arrives. [1]
  8. When anyone calls STOP, the lift pauses. STOP releases every held direction on every phone and shows a full-screen alert to everyone else, so look and confirm with the crew before moving again. [1]
  9. At the end of the shift, everyone leaves the session.

Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] Nobody needs to install an app, because the page runs in a browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] HOLD and SLOW stay on for everyone in the jobsite until the last person leaves. [1]

A phone video call app is another option. Confirm whether the crew can keep the call open for the whole shift, whether the signal person stays in view, and whether the phone locks its screen during the lift.

A two-way radio is a third option. This page has no published details about one, so check that every crew member can hear it over the noise on site, that the crew agrees on plain spoken words, and that the channel stays clear through the lift.

Match the option to the crew and the site. Button presses, chat and voice pass between phones in a browser. [1] Keep a voice or hand-signal fallback ready.

Common mistakes to avoid

Relying on one phone for STOP. If that phone loses its data signal, the rest of the crew may not see the signal, so keep a voice or hand option ready.

Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device. [1]

Leaving HOLD or SLOW on from an earlier part of the shift without knowing it. Those signals stay on for everyone until the last person leaves the jobsite, so the whole crew sees them until then. [1]

Reusing an old link can leave the crew on a link that has expired. A jobsite link stops working 12 hours after the first person joins it. [1]

Expecting an empty session to hold its signals. A jobsite with nobody in it is wiped after 3 idle hours. [1]

Letting a move go unconfirmed. A move that stops arriving for 2 seconds is dropped by the other phones, so the signal person should watch for each move to arrive. [1]

Frequently asked questions

Is OperatorLink free to use for tower crane assembly crews?

OperatorLink is currently free to use, and no paid plan is built yet. [1] Button presses, chat and voice pass between phones in a browser. [1] Before a lift, ask the crew to confirm that every phone can open the page and that the signals reach every phone. Do not rely on the page alone if a phone drops out during the lift.

What happens when someone calls STOP with OperatorLink during a mast lift?

STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [1] The crew should treat that alert as the cue to stop and look before anyone moves again. HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1] Confirm who is in the session before the lift resumes.

How long does an OperatorLink jobsite link stay active?

A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, the person who starts the jobsite should open a fresh session and share the new link or QR code with the crew. [1]

Do OperatorLink signals buzz on every phone?

No. On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone the crew should rely on the screen and the sound. [1] Check the sound settings on every phone before the lift begins, and keep a voice or hand signal ready in case an alert is missed.

Can OperatorLink carry voice calls and radio-style calls between the crew?

Yes. Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Voice runs over the phone's browser and data signal, so the crew should keep a voice or hand-signal fallback ready for the lift. [1]

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons