How to coordinate subsea equipment lowering to the seabed
Steps, checks and tool options for coordinating the lowering of subsea equipment from vessel to seabed, with what to have ready and common mistakes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
A lowering goes well when one plan names who gives each command, every person on the lift sees the same signal, and a backup channel is ready before the load leaves the vessel. OperatorLink is one option for sharing STOP, HOLD and SLOW between phones in a browser. [1]
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | No facts on this page describe it; see the checks below | not published | not published |
| Two-way radio | No facts on this page describe it; see the checks below | not published | not published |
What you need before you start
Before the first load leaves the vessel, the lowering team needs a written plan that names the lift supervisor, the person giving each command, and the handover points where control passes between the vessel and the seabed team. Confirm that the equipment weight, the rigging and the landing area are on the plan, and that every person on the lift has read it.
Agree on a short set of plain commands for move, hold and stop, and make sure each person knows what each one means before the lowering starts. Have a backup channel ready, such as a two-way radio or a second phone, so commands still reach the team if the main one fails.
If a phone-based option is used, check the deck and the work area for a working data signal, because the phones need that signal to pass commands. [1] Decide who will open the shared session and who will hold the link or QR code. [1] If the session is opened early and the team waits, check that it has not been left empty, since a jobsite with nobody in it is wiped after 3 idle hours. [1]
Step by step
- Hold a briefing with every person who will give or receive a command, and read the plan out loud.
- Confirm each phone has a working browser and a data signal for the whole lowering. [1]
- Open the shared session from a phone browser. No app install is needed. [1]
- Share the link or QR code, and have each team member join from it. [1]
- Check that every member is in the session before the load moves, so each person sees the same commands. [1]
- Agree which states stay on for the whole lowering. HOLD and SLOW stay on for everyone in the jobsite until the last person leaves, so clear them on purpose when they are no longer needed. [1]
- Hold a move button to keep sending that move to the other phones. If the move stops arriving for 2 seconds, the other phones drop it, so keep the button held only while the move is being watched. [1]
- Use quick calls such as Go Ahead, Copy That and All Clear to confirm each stage. They are sent as chat messages. [1]
- When STOP is pressed, it releases every held direction on every phone and shows a full-screen alert to everyone else. Stop the lowering, confirm the load's position, and only then give the next command. [1]
- At the end of the lowering, everyone leaves the session.
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] Anyone who joins can take part in a voice call run from the phone browser. [1] Nobody needs to install an app, and the page can be added to a phone's home screen as a standalone app. [1] [1]
A phone video call app is a second option. No facts here describe one, so check whether the call can stay open for the whole lowering, whether the person giving commands can see the load and the landing area on screen, and whether the phone keeps its screen awake during the lift.
A two-way radio is a third option. No facts here describe one, so check that every member of the team can be heard over the noise of the vessel, that commands use the same plain words, and that the channel stays clear for the whole lowering.
Match the option to the team and the work area, and keep a fallback ready for the case where a phone loses its signal.
Common mistakes to avoid
Relying on one phone for STOP. If that phone loses its data signal, the rest of the team does not see the command, so keep a voice or radio option ready.
Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device. [1] If a phone loses its data signal, commands may stop reaching the other phones, so keep a voice or radio option ready. [1]
Leaving a session empty and expecting it to be ready later. A jobsite with nobody in it is wiped after 3 idle hours. [1]
Forgetting that HOLD and SLOW stay on for everyone until the last person leaves, so the team has to clear them on purpose. [1]
Keeping a move button held without watching the load. If a move stops arriving for 2 seconds, the other phones drop it. [1]
Using an old link. A jobsite link stops working 12 hours after the first person joins it. [1]
Frequently asked questions
Is OperatorLink free to use for subsea lowering work?
OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser with no app install. [1] Each phone needs a working data signal for the whole lowering, so check the vessel and work area before relying on it. This page cannot say how pricing may change later, so check the current terms before relying on it.
What happens when STOP is pressed during a lowering in OperatorLink?
STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else, so everyone is alerted. [1] HOLD and SLOW behave differently. They stay on for everyone until the last person leaves the jobsite. [1] Whether an alert is noticed also depends on the phone, since on Android browsers signals make the phone buzz, while iPhone Safari ignores the buzz. [1] Keep a voice or radio check as well.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new lowering, start a fresh session and share the new link or QR code with the team. [1] Check when the first person joined before the day begins, so the team is not caught out by an expired link.
Do STOP signals buzz on every phone in OperatorLink?
Not on every phone. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] On an iPhone the buzz does not happen, so check the sound and the screen on every phone before the lowering starts. Do not rely on a buzz to catch the team's attention. Use a voice or radio check as well, so every person hears the command.
Can OperatorLink be used during a subsea lowering with no phone signal?
OperatorLink passes button presses, chat and voice between phones in a phone browser, so the phones need a working data signal to send and receive them. [1] This page cannot say how the product behaves in areas without coverage, so check the vessel and the work area for a signal before the lowering. Keep a two-way radio or another fallback ready for the case where a phone drops out.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift