How to coordinate machine lifts onto trailers for heavy machinery movers
Coordinate lifting machines onto trailers with a shared phone signal list for heavy machinery movers: steps, tool options and common mistakes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Heavy machinery movers can coordinate lifting machines onto trailers with a clear plan for who gives each signal, and a shared phone session can carry those signals to the whole crew. OperatorLink is one option: STOP shows a full-screen alert to everyone else, and HOLD and SLOW stay on until the last person leaves. [1] [1] Other options are described below, along with what to check for each.
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Heavy machinery movers coordinating a lift onto a trailer need a plan that names who gives each signal, who runs the machine, and who watches the load and the trailer edge. Pick one signal person whose signals the machine operator follows, and agree on a backup in case that person's phone or radio drops out. Walk the path from the machine to the trailer before the move starts, and mark where the trailer sits and where the load will be set down.
If the crew uses OperatorLink, each phone needs a working phone browser, because button presses, chat and voice pass between phones in a browser. [1] The person who starts the session shares a link or QR code, and the crew joins from it. [1] A jobsite link stops working 12 hours after the first person joins it, so start a fresh session for each day's move. [1] Decide who will watch the phone that shows HOLD and SLOW, since those signals stay on for everyone until the last person leaves. [1] Adding the page to the home screen lets it open as a standalone app. [1]
Step by step
These steps apply to any signalling method. The steps that describe OperatorLink say so in their wording.
- Walk the load path with the whole crew before the move and agree on each signal, including who calls STOP.
- If the crew uses OperatorLink, check that each phone has a working browser. [1]
- OperatorLink runs in a phone browser, and no app install is needed. [1]
- The person who starts the session shares the link or QR code, and each crew member joins from it. [1]
- Confirm everyone is in before the machine moves, because it passes button presses, chat and voice between phones in a phone browser. [1]
- Hold a move button to keep sending that move. If it stops arriving for 2 seconds, the other phones drop it, so keep the button held while the load is checked. [1]
- Press STOP as soon as anyone sees a problem. It releases every held direction on every phone and shows a full-screen alert to everyone else, so the crew pauses and looks before moving again. [1]
- One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages, which gives the crew quick replies. [1]
- A jobsite with nobody in it is wiped after 3 idle hours. [1]
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser. [1] Anyone who joins the session can take part in a voice call run from the phone browser. [1] Nobody needs to install an app, because the page runs in a browser. [1] It is currently free to use, and no paid plan is built yet. [1]
A phone video call app is a second option. No facts here describe one, so check whether the crew can keep the call open for the whole move, whether the signal person can keep the load in view, and whether the phone locks its screen during the lift.
A two-way radio is a third option. No facts here describe one, so check that the crew agrees on plain voice calls, that every member can be heard over machine noise, and that the channel stays clear through the move.
Match the option to the crew and the site, and keep a fallback ready. Button presses, chat and voice pass between phones in a browser. [1]
Common mistakes to avoid
Relying on one phone for STOP without a backup signal. Button presses, chat and voice pass between phones in a browser. [1]
Assuming every phone alerts the same way: on Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every phone. [1]
Leaving a session empty and expecting it to be ready the next day: a session with nobody in it is wiped after 3 idle hours. [1]
Reusing yesterday's link: a jobsite link stops working 12 hours after the first person joins it, so start a new session for each day's move. [1]
Forgetting that HOLD and SLOW stay on for everyone and clear only when the last person leaves, so a hold called early may still be on when the crew expects the move to go. [1]
Not confirming that a move still arrives: if a move stops arriving for 2 seconds, the other phones drop it, so keep the button held and watch the load. [1]
Skipping the home screen step before the lift. The app can be added to a phone's home screen as a standalone app. [1]
Frequently asked questions
Is OperatorLink free to use for coordinating trailer lifts?
OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser with no app install, so the crew can open it on the phones they already carry. [1]
What does the STOP signal do in OperatorLink?
STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1] A crew should agree on which signal to use for each situation before the move begins, so nobody has to guess under pressure.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] A session with nobody in it is wiped after 3 idle hours, so a session left empty over a break may need to be started again. [1] For the next day's move, start a new session and share the new link or QR code with the crew. [1]
Does OperatorLink buzz phones when a STOP signal arrives?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz. [1] Check the sound and screen on every phone in the crew before the lift.
Can OperatorLink be used for voice calls during a trailer load?
Anyone who joins the session can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are also sent as chat messages. [1] Keep a radio or hand signal ready as a fallback. Button presses, chat and voice pass between phones in a browser. [1]
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift