2Dig Plain comparisons of crane signalling and jobsite communication tools

Coordinate camera crane moves with the grip team on film sets

Steps, tool choices and common mistakes for coordinating camera crane moves with the grip team on film sets, plus phone signals.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

Agree the move names and the stop word with the grip team before the shot, then confirm everyone hears them. OperatorLink is one option: it shows STOP, HOLD and SLOW on phones in a browser and passes button presses, chat and voice between them. [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows the crew STOP, HOLD and SLOW signals and passes button presses, chat and voice between phones in a phone browser. [1]OperatorLink is currently free to use, and no paid plan is built yet. [1]not published
Phone video call appnot publishednot publishednot published
Two-way radionot publishednot publishednot published

What you need before you start

Before the first move, the crane crew and the grip team should agree who gives each signal, what each signal means, and which phone or radio carries it.

Check that each phone can open a web page in its browser. [1] The person who starts the session shares a link or QR code, and the crew joins from it. [1] Decide which signals stay on for everyone. HOLD and SLOW stay on for everyone in the jobsite and are cleared only when the last person leaves. [1] Keep a voice or hand signal ready as well, because a phone signal can drop in the middle of a shot.

Step by step

The steps below apply whatever signal method the crew chooses. Where a step describes OperatorLink, the sentence carries its marker.

  1. Walk the set with the grip team before the shot and agree on the move names, the stop word, and who calls each move.
  2. Check that each phone can open a web page in its browser. [1]
  3. Have the person who starts the session open it from a phone browser, with no app install needed. [1]
  4. That person shares the link or QR code, and each grip team member joins from it. [1]
  5. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew. [1]
  6. Holding a move button keeps sending that move to the other phones. If it stops arriving for 2 seconds, the other phones drop it. [1]
  7. One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1]
  8. STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1]
  9. At the end of the shift, everyone leaves the session. A jobsite with nobody in it is wiped after 3 idle hours. [1]

Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] Nobody needs to install an app, because the page runs in a browser. [1] Anyone who joins can take part in a voice call run from the phone browser. [1] The page can also be added to a phone's home screen so it opens like a standalone app. [1]

No published facts describe a phone video call app here, so check the points below: whether the call can stay open for the whole shift, whether the operator can see the grip team clearly, and whether the phone locks its screen during a move.

No published facts describe a two-way radio here, so check that the crew agrees on plain voice terms, that each grip team member can be heard over set noise, and that the channel stays clear during a move.

Common mistakes to avoid

Relying on one phone for the STOP signal.

Assuming every phone alerts the same way. Check how each phone alerts, because alerts differ between phones. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1]

Leaving an empty session open and expecting it to hold signals for the next day. A jobsite with nobody in it is wiped after 3 idle hours. [1]

Forgetting that HOLD and SLOW stay on for everyone until the last person leaves. A signal from earlier in the shift can still be showing when the next move begins. [1]

Not watching the load during a held move. If a move stops arriving for 2 seconds, the other phones drop it. [1]

Letting the phone's screen lock during a move. The page can be added to a phone's home screen so it opens as a standalone app. [1]

Frequently asked questions

Is OperatorLink free to use for film and studio crane crews?

OperatorLink is currently free to use, and no paid plan is built yet. [1] The signals run through a phone browser, so check the phone's data plan before the shoot.

What does OperatorLink do when STOP is pressed on a film set?

STOP releases every held direction on every phone in the session. [1] It also shows a full-screen alert to everyone else in the session. [1] HOLD and SLOW behave differently, because they stay on for everyone until the last person leaves the jobsite. [1]

How long does an OperatorLink jobsite link stay active?

A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier shift may no longer open the session. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For a new shift, start a fresh session and share the new link or QR code with the crew. [1]

Does OperatorLink make every phone buzz when a signal arrives?

On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz. [1]

Can OperatorLink carry voice between grip team and crane crew phones?

Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Voice depends on the phone's data signal, so keep a radio or hand signal as a fallback during the shot.

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons