How to confirm the pouring area is clear for foundry crews
Steps for foundry pouring crews to confirm the pouring area is clear before a pour, with checks, tool options and common mistakes.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Confirm the pouring area is clear by walking the full pour path from the furnace or ladle to each mold, checking for people, loose tools, debris and standing water, confirming everyone is out of the path, and getting an agreed clear call from the pour lead or signal person before the pour starts.
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Before a pour, the pour lead needs a clear view of the whole pouring area, from the furnace or ladle path to each mold and the ground beyond it. Have the pour plan in hand so the crew knows which path the molten metal will travel and which spots must stay empty.
Name one person to make the clear call, usually the pour lead or the signal person, and make sure that person can see the full path from where they stand. Keep a list of everyone assigned to the pour, so each person can be accounted for before the area is called clear.
Agree on the call words and the signal in advance, whether by hand, by voice on a radio, or through a phone session, so nobody has to guess what a signal means in the heat and noise. Check that barriers, markers and fire cover are in place where the plan says they should be. Hold a short walk-through with the crew so everyone knows where the pour path runs.
Step by step
- Stop all other work in the pouring area and tell the crew that a clear check is starting.
- Walk the full pour path from the furnace or ladle to each mold, looking at the ground for people, loose tools, debris, standing water and anything that could react with molten metal.
- Confirm that every person assigned to the pour is either at their station or outside the area, and that no one is still in the path.
- Check the barriers, markers, and any overhead loads or lifts that could cross the pour path.
- If a crane or lift is used, confirm its path from the furnace to the mold is clear and that the operator can see the signal person.
- Repeat the walk with the pour lead, so the check is confirmed by someone who is not pouring.
- Make the clear call in the agreed words, and wait for the crew to acknowledge it before the pour starts.
- Recheck the area if anyone enters the path, and make the clear call again before any further pour.
- Record the check on the pour sheet with the time and the name of the person who made the call.
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody needs to install an app, because the page runs in a browser. [1] The person who starts a session shares a link or QR code, and the crew joins from it. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] A STOP signal releases every held direction on every phone and shows a full-screen alert to everyone else. [1] A jobsite link stops working 12 hours after the first person joins it. [1]
A phone video call app is a second option. Details for this option are not published here, so check whether the call stays open for the whole walk, whether the person making the clear call can see the full path from where they stand, and whether the phone's screen stays on during the walk.
A two-way radio is a third option for the crew to consider for voice calls. Details for this option are not published here, so check that the crew agrees on plain voice calls, that every member can hear the clear call over the machine noise, and that the channel stays clear through the lift.
Match the option to the crew and the site. Because a phone session runs in a browser, keep a fallback ready in case a phone connection drops. [1]
Common mistakes to avoid
Making the clear call before the walk is finished, so the call reflects an old view of the area. Relying on one person's view of the path when a gap may only be visible from the far side. Assuming every phone alerts the same way: on Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every phone before the check begins. [1]
Leaving a session open with nobody in it and expecting it to be ready for the next pour, because a jobsite with nobody in it is wiped after 3 idle hours. [1] Forgetting that HOLD and SLOW stay on for everyone in the jobsite until the last person leaves, when they are cleared. [1] Treating a held move button as the only signal: holding a move button keeps sending that move to the other phones, but if it stops arriving for 2 seconds, the other phones stop showing it, so the crew should confirm by voice or hand as well. [1] Skipping the step where the crew acknowledges the clear call before the pour starts.
Frequently asked questions
Is OperatorLink free to use for foundry pouring crews?
OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser with no app install. [1] Check the phone connection at the pouring area before relying on a session. Confirming that the area is clear remains the pour lead's job, with or without a phone session.
What does the STOP signal do in OperatorLink?
STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [1] During a clear check, anyone who sees a person enter the pouring path can call STOP. HOLD and SLOW work differently, because they stay on for everyone until the last person leaves the jobsite. [1] Keep the agreed voice or hand signals as the main calls, so the crew is not depending on a phone alone.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] The jobsite is wiped after 3 idle hours with nobody in it. [1] Once a link has expired, check that the pouring-area check still has a working way to reach the crew before the pour begins.
Do OperatorLink signals buzz on every phone?
On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz, so on an iPhone the alert may only be noticed on the screen. [1] Check the sound and screen settings on every phone before the clear check begins, so no one misses a stop signal from across the pouring area.
Can OperatorLink be used for voice calls during a pour?
Anyone who joins the session can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are also sent as chat messages. [1] Because the session runs in a phone browser, keep a radio or hand signal ready as a fallback. [1] Agree before the pour which call means the area is clear, and remember that a call is only a message, so the crew still needs to look at the path first.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift