2Dig Plain comparisons of crane signalling and jobsite communication tools

How to check lift communication meets site rules

Check that lift communication meets site rules: list required signals, test each method with the crew, and record the result before the lift starts.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

To check that lift communication meets site rules, first write down every signal the site rules require, then test each method with the whole crew before the lift starts. OperatorLink is one option for this check: it shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser [1]Currently free to use, no paid plan built yet [1]not published
Phone video call appnot publishednot publishednot published
Two-way radionot publishednot publishednot published

What you need before you start

Before you check anything, get the site's written communication rules in hand, including what they say about signals, radio calls and who may call a stop. Have the list of lift roles ready, and name the signal person for each lift, so you can confirm that person can be seen and heard by the operator. Gather the phones and radios the crew actually uses and check their batteries, because a method that works in an office may not work on a site. If a phone-based option is on the table, note that it runs in a phone browser, so each phone must be checked before the shift. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] Decide in advance who starts the session, since a jobsite with nobody in it is wiped after 3 idle hours. [1] Finally, confirm in the written rules that phone-based signals are allowed at all.

Step by step

  1. Pull the site's communication rules and list every signal and radio call they require, writing each one down so it can be checked.
  2. Walk the lift with the operator and the signal person, and confirm each required signal can be given and seen from the operator's position.
  3. Test every method the crew plans to use before the lift starts, and run each signal once to confirm the operator responds.
  4. Check that a stop signal reaches every person who needs it, and that each person sees or hears it. If anyone misses it, the method is not ready.
  5. Record which signals stay active until they are cleared and who clears them, and confirm the site rules allow that.
  6. Check how each person is alerted, and confirm the alert is noticed on every device in the crew.
  7. Check that a held move is received by everyone watching it, and that a dropped move is noticed.
  8. Repeat the check after any change of crew, break or new session, so the record matches what happened on the lift.
  9. Write down the result: the date, the people present, each method checked, and anything that failed, so the record can be compared with the site rules.

Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Nobody needs to install an app, because the page runs in a browser. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] Holding a move button keeps sending that move to the other phones. [1] Anyone who joins can take part in a voice call run from the phone browser. [1] For a quick reply, one-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] The page can also be added to a phone's home screen as a standalone app. [1] OperatorLink is currently free to use, and no paid plan is built yet. [1]

A phone video call app is a second option. No facts are available for it here, so check whether the site rules accept a video call as a signal, whether the operator and signal person can each see the other, and whether the phone's screen stays on during the lift.

A two-way radio is a third option. No facts are available for it here, so check that the channel is the one the site rules name, that every crew member can be heard over machine noise, and that the channel stays clear for the whole lift.

Match the option to what the site rules require, and keep a fallback ready for any method that depends on a phone.

Common mistakes to avoid

Relying on one phone for the stop signal. Check the site's rules for what happens if a phone drops out of the session, and keep a voice or hand option ready. Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check sound and screen on every device. [1] Leaving a session empty and expecting it to be there the next day. A jobsite with nobody in it is wiped after 3 idle hours. [1] Reusing an old link. A jobsite link stops working 12 hours after the first person joins it, so share a new one for each shift. [1] Forgetting that HOLD and SLOW stay on for everyone until the last person leaves, so the crew has to clear them on purpose. [1] Assuming a held move is still moving. If a move stops arriving for 2 seconds, the other phones drop it, so keep watching the load. [1] Treating a test as proof of the site rules. A working test shows only that a method worked that day, so the written rules still have to be checked against the record.

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet. [1] Because it runs in a phone browser with no app install, a crew can open it on the phones they already carry. [1] Whether it meets the site's own rules is a separate question, and the written rules are the place to check that before relying on any signal method.

What does the STOP signal do in OperatorLink?

STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [1] HOLD and SLOW work differently: they stay on for everyone in the jobsite and are cleared only when the last person leaves. [1] Check which of these signals the site rules require, and make sure each one is clear to the whole crew before the lift begins.

How long does an OperatorLink jobsite stay open?

A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier shift may no longer open the session. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] For each new shift, start a fresh session and share the new link or QR code with the crew.

Do STOP signals in OperatorLink buzz every phone?

On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] Check how each phone alerts the crew, because the alert is not the same on every device. Test the alert on every phone in the crew before the lift, using the settings the phone will use on site.

Can OperatorLink be used for voice during a lift?

Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Whether voice or chat counts as a valid lift call under the site rules is not covered here, so check the written rules first and keep a hand signal or radio as a fallback.

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons