2Dig Plain comparisons of crane signalling and jobsite communication tools

How to call stop when equipment catches on a shaft opening

Steps for elevator installers to call stop when equipment catches on a shaft opening, what to have ready, and common mistakes to avoid.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

Agree on one stop signal and who gives it before any movement, then call it at once when equipment catches, keeping everyone clear until the catch is checked. If you use OperatorLink, STOP shows a full-screen alert to everyone else in the session. [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1]Currently free to use, no paid plan built yet [1]not published
Two-way radionot publishednot publishednot published
Phone video call appnot publishednot publishednot published

What you need before you start

Before any equipment moves near a shaft opening, the crew should agree on one stop signal and on who gives it. Everyone on the crew needs to know that signal before the first move, and the person who can see where the equipment meets the opening should be the one watching for a catch. Keep a second way to reach the operator, since a single device or a single person can fail at the wrong moment.

If the crew uses OperatorLink, the person who starts the jobsite shares a link or QR code, and the rest of the crew joins from it. [1] Button presses, chat and voice pass between phones in a browser. [1] Nothing needs to be installed as an app, since the session runs in the browser. [1] A session with nobody in it is wiped after 3 idle hours, so start it fresh at the beginning of each shift. [1] A jobsite link also stops working 12 hours after the first person joins it. [1]

Before the job starts, check that each phone's connection works and that its screen stays on while someone is watching it. Agree on who holds each phone and where it will be during the move.

Step by step

  1. Agree on the stop signal and on who gives it before any equipment moves.
  2. Keep everyone clear of the equipment and the shaft opening while it moves, and keep the person giving signals in view of the equipment.
  3. When the equipment catches, the person who sees it calls STOP at once, by voice, by hand or on the phone.
  4. Everyone stops and stays clear until the catch has been checked from a safe spot.
  5. If you use OperatorLink, pressing STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1]
  6. If you use OperatorLink, holding a movement button keeps sending its signal to the other phones; if it stops arriving for 2 seconds, the other phones stop showing it. [1]
  7. HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1]
  8. Once the equipment is free and every person confirms it is clear, restart the move only after a fresh call from the person giving signals.
  9. Afterwards, write down what caught and what cleared it, so the crew can change the plan before the next shift.

Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1] Anyone who joins can take part in a voice call run from the phone browser, and one-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] [1] The page can also be added to a phone's home screen as a standalone app. [1]

A two-way radio is a second option. This page has no published facts about one, so check that every member of the crew can hear and be heard over the noise around the shaft and the equipment, and that the channel stays clear for the whole move.

A phone video call app is a third option. This page has no published facts about one, so check whether the call can stay open for the whole shift, whether the person giving signals stays in view of the equipment, and whether the phone's screen locks during a move.

Match the option to the crew and the site, and keep a second method ready, since any one phone or radio can fail at the wrong moment.

Common mistakes to avoid

Relying on one phone or one person to call stop. If that phone or person is out of reach, the crew has no other way to stop the move, so keep a voice or hand signal ready as well.

Assuming every phone alerts the same way. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check the sound and screen on every device before the first move. [1]

Reusing an old session. A jobsite with nobody in it is wiped after 3 idle hours, so start a new session for each shift. [1]

Forgetting that HOLD and SLOW stay on until the last person leaves, which keeps a hold in place after the crew has moved on. [1]

Expecting a movement signal to remain visible after releasing the button. Holding a movement button keeps sending its signal to the other phones; if it stops arriving for 2 seconds, the other phones stop showing it. [1]

Letting the phone lock its screen during a move. Check the screen settings on each phone before the shift so the alert can be seen when it arrives.

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser with no app install, so the crew joins without installing anything. [1] Check the current terms on the site before you depend on it for a job.

What does STOP do in OperatorLink?

STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] HOLD and SLOW work differently, since they stay on for everyone in the jobsite and are cleared when the last person leaves. [1] Keep a plain voice or hand signal ready as well, so the crew can still call stop if a phone is not in front of the person giving signals.

How long does an OperatorLink jobsite link stay active?

A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours, so a session left over from an earlier shift may need to be started again. [1] Before each shift, the person who starts the jobsite opens a fresh session and shares a new link or QR code with the crew.

Do STOP signals buzz every phone in OperatorLink?

No, not on every phone. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz. [1] On an iPhone, the crew should also check the full-screen alert, which STOP shows to everyone else. [1] Check the sound and screen on each device during setup, before the first move.

Can OperatorLink be used for voice calls during an elevator install?

Anyone who joins a jobsite can take part in a voice call run from the phone browser. [1] One-tap calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1] Check on each phone that the call works before the shift starts, and keep a second way to call stop ready in case the call drops.

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons