2Dig Plain comparisons of crane signalling and jobsite communication tools

How to call hold for plate alignment on tank erection crews

Steps for calling hold while checking plate alignment on a tank erection crew, with what to have ready, tool options and common mistakes.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

Name one signal person, agree on the HOLD call before any plate moves, and have every crew member stop and confirm before the check starts. OperatorLink can show HOLD to the crew in a phone browser, and it is currently free to use. [1] [1]

OptionWhat it doesFeeCard fee
OperatorLinkShows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1]Currently free to use, no paid plan built yet [1]not published
Phone video call appnot publishednot publishednot published
Two-way radionot publishednot publishednot published

What you need before you start

Tank erection crews need one signal person who calls HOLD, a short agreement on what each signal means, and a way for every crew member to see or hear the call from where they stand. Agree on these before the check starts, so nobody has to guess while plates are being lined up. Decide how close the crew must stay to the plate edge and whether the signal person can see every member from their position. If the crew calls HOLD on phones, each phone needs a browser, because the signals pass between phones in a phone browser. [1] The person who starts the shared session shares a link or QR code, and the rest of the crew joins from it. [1] Keep a backup such as a radio or a hand signal, in case a phone drops out of the session during the check.

Step by step

  1. Name one signal person for the check, and tell the crew that only that person calls HOLD.
  2. Before anyone moves a plate, the signal person calls HOLD so the whole crew can see or hear it.
  3. Each crew member stops, moves clear of the plate edge, and confirms they have stopped.
  4. Check the plate alignment with the tools the crew normally uses, and keep the signal person in view of the crew throughout.
  5. When the check is finished, the signal person tells the crew and confirms that everyone is ready before anyone moves again.
  6. If a crew member sees a problem during the check, they stop and tell the signal person before the crew moves again.

Repeat the same steps for each plate, so the crew builds the same habit every time. A quick check is not a reason to skip the confirmation.

Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] A HOLD stays on for everyone in the jobsite until the last person leaves, so the crew should plan for it to remain on after the check ends. [1] Nobody needs to install an app, because the page runs in a browser. [1] The person who starts the session shares a link or QR code, and the crew joins from it. [1]

A phone video call app is another option. For this job, check whether the signal person can stay in view of the crew, whether the call stays open for the whole check, and whether the phone locks its screen during the check.

A two-way radio is a third option. For this job, check that every crew member can hear it over the noise on site, that the crew agrees on the words used for HOLD, and that the channel stays clear for the length of the check.

Match the option to the crew and the site, and keep a fallback ready in case a phone drops out during the check.

Common mistakes to avoid

Calling HOLD from one phone and assuming every crew member saw it. If that phone drops out, the others may not see the call, so keep a hand or radio signal ready.

Expecting alerts to behave the same on every phone. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so the crew should check the screen and sound on every phone before the check. [1]

Assuming HOLD goes off when the check ends. HOLD stays on for everyone until the last person leaves the jobsite, so the crew should agree what happens next while it stays on. [1]

Trusting a held move button without watching it. Holding a move button keeps sending that move to the other phones, and if it stops arriving for 2 seconds, they drop it, so the signal person should keep watching the crew. [1]

Reusing a session link from an earlier shift. A jobsite link stops working 12 hours after the first person joins it. [1]

Frequently asked questions

How do you call hold while checking plate alignment on a tank erection crew?

Name one signal person, agree on the HOLD call before any plate moves, and have every crew member stop and confirm before the check starts. The signal person calls HOLD where the whole crew can see or hear it, and the check begins only after each person confirms. Keep a radio or hand signal ready in case a phone drops out, since a connection can fail partway through a shift. When the check is complete, the crew should agree on what happens next before anyone moves again.

Is OperatorLink free to use for tank erection crews?

OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser with no app install, so nothing has to be installed before the crew can join. [1] Check how much data your phones use for a shift before relying on them, since each phone needs to stay connected for the whole check.

Does a HOLD signal in OperatorLink stay on until someone clears it?

HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1] That means a HOLD called for one plate check can stay on while the crew moves to the next task, so agree in advance what the crew does while it is on. STOP stops any move that a phone is still holding down, on every phone, and shows a full-screen alert to everyone else. [1]

How long does an OperatorLink jobsite link stay active for a crew?

A jobsite link stops working 12 hours after the first person joins it, so a link from an earlier shift may no longer open the session. [1] A jobsite with nobody in it is wiped after 3 idle hours, so start a fresh session for each shift. [1] The person who starts the jobsite shares a link or QR code with the crew, and each member joins from it. [1] Share the new link at the start of the shift so every member can join before the check begins.

Does OperatorLink buzz iPhones when STOP is pressed?

On Android browsers, signals such as STOP make the phone buzz. [1] iPhone Safari ignores the buzz. [1] STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] Check the screen and sound settings on every phone in the crew before the lift. Plan another way for iPhone users to notice a STOP, such as a visual check or a voice call.

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)

Related comparisons