How to call hold while checking connection alignment
Steps, tool options and common mistakes for amusement ride installers who need one agreed hold call while checking connection alignment on site.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
Calling hold while checking connection alignment depends on one agreed call that every installer knows before work starts. The rest is choosing how that call reaches each person and checking that it does.
| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a phone browser [1] | Currently free to use, no paid plan built yet [1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |
What you need before you start
Start with a plan that names who calls hold, who may release it, and which installer checks the connection alignment. Write the exact words for hold and for stop, and agree on them before the work begins, so nobody has to think of a call in the middle of a check.
Make sure every installer can see or hear the call from where they stand, and that the person checking alignment can keep the connection point in view while they work. Decide what happens if two people call at once, and who has the final say. Name a spare person who can call hold if the caller becomes unable to.
Check that each phone, radio or other device has charge and a working connection for the whole check. If the crew uses a phone tool, have everyone open it and confirm it works before the check starts, not during it. Keep a fallback call ready, such as a spoken word or a raised hand, in case one device stops working.
Step by step
- Confirm every installer is in place and knows the hold call before anyone touches the connection.
- Name the connection point and the person checking its alignment, so everyone knows what is being held.
- Ask each installer to acknowledge the plan with a short reply, so the caller knows each person is ready.
- Call hold using the agreed words, and keep it in force until the check is complete.
- Each installer confirms they received the hold call before the alignment check continues.
- Check the alignment while the hold stays in place, and report any gap or offset in plain words.
- If anyone sees a problem, call stop at once. Do not wait for the others to finish their step.
- When the check is done and the alignment is confirmed, the caller releases hold using the agreed words, and the crew confirms the release before the work resumes.
Keep each call short, so it stays clear over the noise on site. Repeat the hold call if anyone is unsure they heard it, and do not move the connection while any installer has not confirmed the hold.
Where the site allows it, the caller should not be the person doing the alignment check. One person can then focus on the connection while another keeps the calls clear.
If the check takes longer than planned, restate the hold at the start of each new stage, so no one assumes it has lapsed.
Tools that can do it
OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [1] [1]
It runs in a phone browser with no app install, and the person who starts the session shares a link or QR code that the crew uses to join. [1] [1] HOLD stays on for everyone in the jobsite and is cleared when the last person leaves. [1] STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [1]
Anyone who joins can take part in a voice call run from the phone browser. [1] The app can also be added to a phone's home screen as a standalone app. [1]
A phone video call app is a second option. No facts here describe one, so check whether the call stays connected for the whole check, whether the person checking alignment can keep the screen in view, and whether the phone locks its screen during the check.
A two-way radio is a third option. No facts here describe one, so check that every installer can hear the call over the noise on site, that everyone uses the same agreed words, and that the channel stays clear while the check runs.
Choose the option the crew can run in the conditions on site, and keep a fallback ready in case a phone or connection drops.
Common mistakes to avoid
Calling hold without naming the connection point leaves installers unsure what is being held.
Assuming every phone alerts the same way causes missed signals. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz, so check sound and screen on every device. [1]
A jobsite with nobody in it is wiped after 3 idle hours. [1]
Reusing an old link can leave the crew locked out. A jobsite link stops working 12 hours after the first person joins it. [1]
HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves. [1]
Relying on one device to carry every call is risky, because when that device fails, the caller may lose the way to call hold. Arrange another way to call hold if the device fails, and agree on it before the check begins.
Frequently asked questions
Is OperatorLink free to use?
OperatorLink is currently free to use, and no paid plan is built yet. [1] It runs in a phone browser with no app install, so each phone needs a working connection for the whole check. [1] [1] Before relying on it, confirm the price and terms with the team that publishes this site, since prices can change.
What happens when STOP is pressed on OperatorLink?
STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [1] HOLD and SLOW behave differently, since they stay on for everyone in the jobsite until the last person leaves. [1] Agree in advance which words the crew uses to stop and which to hold, so nobody has to choose during a check.
How long does an OperatorLink jobsite link stay active?
A jobsite link stops working 12 hours after the first person joins it. [1] A jobsite with nobody in it is wiped after 3 idle hours. [1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [1] Do not rely on a link from an earlier shift.
Do STOP signals buzz on every phone with OperatorLink?
On Android browsers, signals such as STOP make the phone buzz, but iPhone Safari ignores the buzz, so the answer differs by phone. [1] Check the sound and screen on every phone before the check begins, so no installer misses a signal. The crew should agree on a spoken or hand signal as a backup.
Can OperatorLink carry voice calls between installers?
Anyone who joins the jobsite can take part in a voice call run from the phone browser. [1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are also available, and they are sent as chat messages. [1] Keep a backup call ready, such as a spoken word or a hand signal, in case a phone or connection drops during the check.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- How to assess crane signal trainees passing calls clearly
- How to assign crane crews to jobs for crane dispatchers in 2026
- How to assign who gives signals during a pick for lift planners
- How MEWP crews call a stop near overhead hazards
- Calling material lifts to upper decks for scaffolding crews
- How to call hold during tight lifts for plant riggers
- How to call hold when a hose shifts under pressure
- Call hold when a load goes out of level
- Call HOLD when a load nears live process equipment
- How to call hold when a load shifts during a lift