2Dig Plain comparisons of crane signalling and jobsite communication tools

Clear-Com vs Sordin in 2026

Clear-Com and Sordin for a crane crew, set beside OperatorLink's jobsite signals: listed prices, setup, and how to choose.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

A crane crew member needs to get signals to the whole crew while the crane moves. OperatorLink shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1]. Clear-Com's cited pages describe partyline workflows that run without intercom hardware [2] and communication for industrial and critical settings, including public safety and transportation [3]. The Sordin listings cited on this page give prices for its products [4]. A crew whose needs go beyond these sources should check each vendor directly before choosing.

OptionOwn feeCard fee
Clear-Comnot publishednot published
SordinX2 Shooting Kit listed at 4 299 kr [4]; SmartEar Impulse listed at 299 kr [4]; Full Flex Kit listed at 5 549 kr [4]not published
OperatorLinkFree to use; no paid plan is built yet [1]not published

The short answer

A crane crew member needs to get signals to the whole crew while the crane moves. OperatorLink shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1]. Clear-Com's cited pages describe partyline workflows that run without intercom hardware [2] and communication for industrial and critical settings, including public safety and transportation [3]. The Sordin listings cited on this page give prices for its products [4]. Clear-Com's sources match a crew that wants partyline calls without intercom hardware, or one working in industrial settings. OperatorLink's sources match a crew that needs a stop to reach every phone. Its cited Sordin facts do not say which signals its products pass, so a crew with that need should check Sordin directly.

What Clear-Com, Sordin is built for

Clear-Com's pages, as cited on this page, describe three things. They say its Gen-IC enables real-time partyline workflows without the need for intercom hardware [2]. They say it serves the industrial and critical communications market, with real-time communications for safety and efficiency in marine and offshore, medical, power and utilities, oil and gas, public safety, transportation and retail [3]. They also say it serves the military, aerospace and government market with communication for command and control, training and simulation, testing and evaluation, and net-centric communications [3].

Sordin's pages cited on this page list product prices, such as the X2 Shooting Kit at 4 299 kr [4]. The Sordin facts gathered for this page do not describe what its kits do on a jobsite, so check its product pages for that before you choose.

What OperatorLink is built for

OperatorLink is made by the team that publishes this site. For a crane crew member, it shows STOP, HOLD and SLOW to the jobsite crew, and passes button presses, chat and voice between phones in a browser [1]. A STOP releases every held direction on every phone and shows a full-screen alert to everyone else [1]. HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves [1]. Holding a move button keeps sending that move to the other phones, and if the move stops arriving for 2 seconds, the other phones drop it [1]. One-tap messages such as Go Ahead, Copy That and All Clear are sent as chat [1]. Anyone who joins can take part in a voice call run from the phone browser [1].

Pricing and fees

Clear-Com's cited pages give no price, so its price is not published here. Sordin lists prices in kronor for its products. Its X2 Shooting Kit is listed at 4 299 kr [4], its SmartEar Impulse at 299 kr [4], and its Full Flex Kit at 5 549 kr [4]. The card fee is not published for any option in the table. OperatorLink is currently free to use, and no paid plan is built yet [1]. A crew that expects to pay a card fee should ask each provider for it before choosing.

Setting it up on a jobsite

OperatorLink runs in a phone browser with no app install [1]. The person who starts a jobsite shares a link or QR code, and the crew joins from it [1]. The app can be added to a phone's home screen as a standalone app [1]. A jobsite link stops working 12 hours after the first person joins [1], and a jobsite with nobody in it is wiped after 3 idle hours [1]. Button presses, chat and voice pass between phones in the browser [1].

For Clear-Com and Sordin, the facts gathered for this page do not describe how a crew is added, how signals pass, or how a jobsite is started. Check each vendor's setup steps before a shift.

Things to check before you choose

Does the crew need a stop that reaches every phone, or partyline calls that run without intercom hardware? Each answer points to a different set of sources, so decide which need comes first.

Which phones does the crew use? On Android browsers a signal such as STOP makes the phone buzz, but iPhone Safari ignores the buzz, so check whether a buzz alert matters for your crew [1].

Does a jobsite link that stops working 12 hours after the first person joins suit your shifts? [1]

Which Sordin product fits the crew's needs, and what does it cost on Sordin's listing?

Which signals does the crew need on a jobsite, and how will you test that each tool passes them before a lift?

How to choose

If the crew needs a stop that reaches every phone, OperatorLink's sources describe a STOP that releases every held direction and shows a full-screen alert to everyone else [1]. If the crew needs HOLD and SLOW to stay on for everyone until the jobsite empties, OperatorLink's sources describe that as well [1]. If the crew wants partyline calls without intercom hardware, Clear-Com's page describes Gen-IC for that [2]. If the crew works in industrial or public safety settings, Clear-Com's page says it serves those markets [3]. If a listed price is the deciding factor, Sordin's pages give prices such as 299 kr for the SmartEar Impulse [4]. If the crew wants a free start, OperatorLink is currently free to use [1]. A crew that needs more than one of these should check each option against each need, because no single source here covers all of them.

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet [1]. The sources cited on this page give no other price for it, and the card fee is not published. Prices can change, so confirm the current terms with the product before a shift. A crew with a budget decision to make should check the latest terms directly before relying on this.

Does Clear-Com offer partyline calls without intercom hardware?

Clear-Com's page says real-time group voice calls can run without intercom hardware [2]. The page cited for this answer does not say how Gen-IC is set up or what it costs, so check those with Clear-Com before deciding. A crew that needs a stop signal reaching every phone should compare that need against OperatorLink's sources, which describe a different set of signals.

How much does the Sordin SmartEar Impulse cost?

Sordin lists the SmartEar Impulse at 299 kr [4]. The Sordin facts gathered for this page do not give a card fee or any shipping charge for it, so check the listing for those. Prices shown on a product page can change, so confirm the current figure with Sordin before ordering. The same listing does not describe what the product does on a jobsite, so review its page for that before choosing.

Does OperatorLink work on iPhone?

OperatorLink runs in a phone browser with no app install [1]. A phone can add the app to its home screen as a standalone app [1]. On Android browsers, signals such as STOP make the phone buzz, but iPhone Safari ignores the buzz [1]. A crew with iPhones should check whether the on-screen alert is enough for its needs.

How long does an OperatorLink jobsite link last?

A jobsite link stops working 12 hours after the first person joins it [1]. A jobsite with nobody in it is wiped after 3 idle hours [1]. The person who starts a jobsite shares a link or QR code, and the crew joins from it [1]. A crew whose shift runs past 12 hours should start a new jobsite with a fresh link. [1]

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)
  2. Clear-Com, clearcom.com/products/wireless, read 2026-10-09
  3. Clear-Com, clearcom.com, read 2026-10-09
  4. Sordin, sordin.com, read 2026-10-16

Related comparisons