Crane communication headsets for offshore crane crews
Compare crane communication headsets and push-to-talk options for offshore crane crews, covering noise, crew connection, shipping and price.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
OperatorLink is currently free to use, with no paid plan built yet [1]. It runs in a phone browser, where it shows STOP, HOLD and SLOW to the jobsite crew [1]. Sensear's Smart Headsets are described for face-to-face talk in noise levels up to 95 dB(A) [2]. Setcom's LiberatorMAX system allows full-duplex communication with no push-to-talk requirement [3]. Eartec's EPak and PRO16 systems each allow up to 16 users on the same setup [4]. Compare the options against the noise on the deck, the size of the crew, and the price before choosing.
| Option | What it does | How the crew connects | Price |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the jobsite crew in a phone browser [1] | Crew joins from a shared link or QR code; the link stops working 12 hours after the first person joins [1][1] | Free to use; no paid plan built yet [1] |
| Eartec | Two systems: EPak with Lazer-Pro, and PRO16 with Monarch [4] | Up to 16 users connect and communicate on the same setup [4] | Not published |
| Setcom | LiberatorMAX system allows full-duplex communication with no push-to-talk requirement [3] | Set both headsets to the same channel to talk to the crew [3] | Not published |
| Sensear | Smart Headsets for face-to-face talk in noise levels up to 95 dB(A) [2] | Not published | Not published |
What offshore crane crews need from crane communication headsets
Offshore crane crews work on a deck or platform where wind, engine noise and the motion of the sea make a spoken call hard to hear. A crane operator often cannot see the whole lift, so a signal person or rigger on the deck relays direction, and the crew needs to know at once when a move must stop. Crew members wear hearing protection and gloves, and they often work in rain or spray, so a headset has to stay comfortable and easy to use through a full shift. Communication may run between the operator in the cab, the signal person on deck, and a supervisor, sometimes across several lifts at once. Crews also need a clear channel so that one conversation does not talk over another. Before choosing a tool, a crew should check how it handles noise, how many people it connects, what each person must do to join, and whether the signal reaches every part of the platform where the crew works. The sections below set out what each option publishes so that the crew can compare them.
OperatorLink for offshore crane crews
OperatorLink is made by the team that publishes this site. It runs in a phone browser with no app install, and it can be added to a phone's home screen as a standalone app [1][1]. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a browser [1][1]. STOP releases every held direction on every phone and shows a full-screen alert to everyone else [1]. HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves [1]. Anyone who joins can take part in a voice call run from the phone browser [1]. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz [1]. OperatorLink is currently free to use, and no paid plan is built yet [1]. Crews that need a headset worn on the body should weigh that need before choosing a phone-based tool.
Eartec for offshore crane crews
Eartec offers two systems, EPak with Lazer-Pro and PRO16 with Monarch [4]. Both the EPak and PRO16 systems allow up to 16 users to connect and communicate simultaneously on the same setup [4]. The Lazer-Pro headsets carry an IP65 rating, which Eartec's page describes as dust and water resistance [4]. Eartec deducts the shipping fee from a refund when a customer chooses Expedited shipping and returns the set [4]. A crew comparing Eartec with the other options should ask Eartec for its price before deciding.
Setcom for offshore crane crews
Setcom's LiberatorMAX system is up and running 30 seconds after the box is opened, and it allows full-duplex communication with no push-to-talk requirement [3]. Set both headsets to the same channel to talk to the crew [3]. Full-duplex means a person can talk and hear at the same time, which matters when a crew calls signals while another person is speaking. A crew should confirm that the system carries signals across the whole platform before relying on it, and ask Setcom for its price before choosing.
Sensear for offshore crane crews
Sensear's patented SENS Technology enhances speech while suppressing background noise [2]. Its Smart Headsets let workers communicate face-to-face in noise levels up to 95 dB(A), and communicate over two-way radio and Bluetooth on mobile phones in noise levels up to 120 dB(A) [2]. Charge racks can accommodate up to 45 headsets for large-scale operations and 6 headsets for smaller needs [2]. A crew working in very loud conditions should compare these noise limits with the levels measured on its own deck.
Matching the tool to the job
A signal person on a loud deck can compare Sensear's Smart Headsets, which are described for face-to-face talk in noise levels up to 95 dB(A) [2]. A crew of up to 16 people that wants one setup can look at Eartec's EPak or PRO16 systems, which both allow up to 16 users on the same setup [4]. A crew that wants talk with no push-to-talk requirement can look at Setcom's LiberatorMAX, which allows full-duplex communication with no push-to-talk requirement [3]. A crew that needs one STOP seen on every phone can use OperatorLink, where STOP releases held directions and shows a full-screen alert to everyone else [1], and HOLD and SLOW stay on until the last person leaves [1]. A crew working where dust and water are present can check the IP65 rating on Eartec's Lazer-Pro headsets [4]. A crew on a short job that already carries phones can start a jobsite from a shared link or QR code [1]. Crews that need a headset worn on the body should weigh that need before choosing a phone-based tool.
Questions to ask before you choose
Does a direction stay on every screen until each person confirms it, or does it clear once the sender lets go? Can the headsets run on the same channel as the crew's phones, or do the two need separate setups? How many people does the crew need to connect at one time, and does the system handle that number on one setup? How far does the system reach across the platform, and where are the dead spots? Who pays for the system, is the price per user, per headset, or per month, and does an annual plan change it? What must each person do to join, and how long does a link stay open? Does the crew need a hands-free headset worn on the body, or is a phone in a pocket enough? Which devices does the crew already carry, and does each tool run on them? What does each provider's return policy say about shipping charges if a set is sent back?
Frequently asked questions
Does OperatorLink work on an offshore crane crew's phones?
OperatorLink runs in a phone browser with no app install, and the app can be added to a phone's home screen as a standalone app [1][1]. Button presses, chat and voice pass between phones in a browser [1]. On Android browsers, signals such as STOP make the phone buzz, while iPhone Safari ignores the buzz [1]. A crew that relies on the buzz should test which phones it carries before the shift starts.
Does Eartec deduct shipping from a refund?
Eartec deducts the shipping fee from a refund when a customer chooses Expedited shipping and returns the set [4]. Before ordering, a crew should check what a return would cost under the shipping option it picks.
How quickly is Setcom's LiberatorMAX ready to use?
The LiberatorMAX system is up and running 30 seconds after the box is opened [3]. It allows full-duplex communication with no push-to-talk requirement [3]. Set both headsets to the same channel to talk to the crew [3]. Before the first lift, a crew should check that every headset is on the same channel.
How many Sensear headsets can one charge rack hold?
Sensear's Charge Racks can accommodate up to 45 headsets for large-scale operations and 6 headsets for smaller-scale needs [2]. Sensear's patented SENS Technology enhances speech while suppressing background noise [2]. A crew should match the rack size to the number of people who wear headsets on a shift.
Does a jobsite link in OperatorLink stay open for a whole shift?
A jobsite link stops working 12 hours after the first person joins it [1]. A jobsite with nobody in it is wiped after 3 idle hours [1]. The person who starts the jobsite shares a link or QR code, and the crew joins from it [1]. A crew on a longer shift should plan to start a new jobsite once the link has expired.
OperatorLink is currently free to use, and no paid plan is built yet. [1]
Try OperatorLinkSources
Related comparisons
- Crane communication headsets compared
- Crane communication headsets for aircraft recovery crews
- Crane communication headsets for amusement ride installers
- Crane communication headsets for apprentice riggers in 2026
- Crane communication headsets for boom truck operators
- Crane communication headsets for bridge construction crews
- Crane communication headsets for bridge crews
- Crane communication headsets for bulk material handlers
- Crane communication headsets for concrete pump operators
- Crane communication headsets for foremen in 2026