2Dig Plain comparisons of crane signalling and jobsite communication tools

Motorola Solutions WAVE PTX vs TASSTA in 2026

Compare Motorola Solutions WAVE PTX and TASSTA with OperatorLink for a crane crew: what each does, published prices, jobsite setup and how to choose.

By 2Dig ยท

2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.

Motorola Solutions WAVE PTX and TASSTA are covered on this page only by the facts their own pages supply, and those facts do not describe how signals reach a crew on a jobsite. OperatorLink shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a browser [1]. Which tool fits depends on the signals your crew needs and the phones it uses.

OptionOwn feeCard fee
Motorola Solutions WAVE PTXnot publishednot published
TASSTAnot publishednot published
OperatorLinkFree to use; no paid plan is built yet [1]not published

The short answer

A crane crew member needs signals to reach the whole crew while the crane moves. OperatorLink shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [1]. Motorola Solutions WAVE PTX's cited page describes SafetyCam, which combines video, voice and an Assist AI-powered wearable to protect staff [2]. TASSTA's cited page says it has over 10 years of experience in mission-critical communication solutions [3]. The cited sources for the two rivals do not describe jobsite signals, so a crew with that need should check each provider directly before choosing.

What Motorola Solutions WAVE PTX and TASSTA are built for

Motorola Solutions WAVE PTX's cited pages describe SafetyCam, which combines video, voice and an Assist AI-powered wearable to protect staff [2]. The same company says it provides managed and support services for keeping customers' technology secure and up to date [2], and it has completed its acquisition of D-Fend Solutions [2]. None of these cited facts describes how signals reach a crew on a jobsite, so this page does not say what WAVE PTX does for that job.

TASSTA's cited page says it has over 10 years of experience in mission-critical communication solutions [3]. The facts gathered for this page do not say what TASSTA's app does on a jobsite, so the crew should check its features with TASSTA before choosing.

What OperatorLink is built for

OperatorLink is made by the team that publishes this site. For a crane crew member, it shows STOP, HOLD and SLOW to the jobsite crew, and passes button presses, chat and voice between phones in a browser [1]. A STOP releases every held direction on every phone and shows a full-screen alert to everyone else [1]. HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves [1]. Holding a move button keeps sending that move to the other phones, and if it stops arriving for 2 seconds, they drop it [1]. One-tap messages such as Go Ahead, Copy That and All Clear are sent as chat [1]. Anyone who joins can take part in a voice call run from the phone browser [1].

Pricing and fees

No price is published for Motorola Solutions WAVE PTX on this page, because the facts gathered for it do not give one. The same is true of TASSTA, whose cited page gives its years of experience but no price [3]. OperatorLink is currently free to use, and no paid plan is built yet [1]. The card fee is not published for any of the three options. A crew that expects to pay a card fee should ask each provider for it before choosing. Prices can change, so confirm the current terms with each provider before a shift.

Setting it up on a jobsite

OperatorLink runs in a phone browser with no app install [1]. The person who starts a jobsite shares a link or QR code, and the crew joins from it [1]. The app can be added to a phone's home screen as a standalone app [1]. A jobsite link stops working 12 hours after the first person joins it [1], and a jobsite with nobody in it is wiped after 3 idle hours [1]. Button presses, chat and voice pass between phones in the browser [1].

The cited facts for Motorola Solutions WAVE PTX do not describe how a crew joins a jobsite or how signals pass between phones, so check both with Motorola Solutions before a shift. The cited TASSTA page does not describe those steps either, so confirm them with TASSTA directly.

Things to check before you choose

Which signals does the crew need on a jobsite, and how will you check that each tool passes them before a lift?

Does the crew need a stop that reaches every phone at once? OperatorLink's sources describe that [1].

Which phones does the crew use? On Android browsers a signal such as STOP makes the phone buzz, but iPhone Safari ignores the buzz, so check whether a buzz alert matters for your crew [1].

Does your organization need an on-premise option, or is a cloud service enough?

What will each provider charge after any trial or for a paid plan, and what card fee applies?

How to choose

If the crew needs a stop that releases every held direction on every phone, OperatorLink's sources describe that [1]. If the crew needs HOLD and SLOW to stay on for everyone until the last person leaves the jobsite, OperatorLink's sources describe that as well [1]. If the crew needs a free start with no paid plan, OperatorLink is currently free to use [1]. If the crew needs video and voice to protect staff, the cited Motorola Solutions WAVE PTX page describes SafetyCam for that [2]. If the crew wants a provider that cites over 10 years of experience in mission-critical communication solutions, TASSTA's page says so [3]. A crew with more than one need should check each option against every need, because the sources here do not cover all of them for any single tool.

Frequently asked questions

Is OperatorLink free to use?

OperatorLink is currently free to use, and no paid plan is built yet [1]. The card fee is not published for it, so a crew that expects to pay one should check before choosing. Prices can change, so confirm the current terms with the product before a shift that depends on them.

Is TASSTA free to use?

The facts gathered for this page give no TASSTA price, so no price is published here. TASSTA's cited page says it has over 10 years of experience in mission-critical communication solutions [3]. That line describes the company's history, not what it costs. Check TASSTA directly for its current terms before choosing a plan for a crew.

Does OperatorLink work on iPhone?

OperatorLink runs in a phone browser with no app install [1]. A phone can add it to its home screen as a standalone app [1]. On Android browsers, signals such as STOP make the phone buzz, but iPhone Safari ignores the buzz [1]. A crew with iPhones should check whether the on-screen alert is enough for its needs.

What does Motorola Solutions WAVE PTX's SafetyCam do?

Motorola Solutions says SafetyCam combines video, voice and an Assist AI-powered wearable to protect staff [2]. The facts gathered for this page do not describe how SafetyCam is set up or what it costs, so check both with Motorola Solutions before deciding. A crew that needs signals such as STOP or HOLD should check whether this product handles them, because the cited facts do not say.

How long does an OperatorLink jobsite link last?

A jobsite link stops working 12 hours after the first person joins it [1]. A jobsite with nobody in it is wiped after 3 idle hours [1]. The person who starts a jobsite shares a link or QR code, and the crew joins from it [1]. A crew whose shift runs past 12 hours should start a new jobsite with a fresh link.

OperatorLink is currently free to use, and no paid plan is built yet. [1]

Try OperatorLink

Sources

  1. OperatorLink's own description of itself (the product of this site's publisher)
  2. Motorola Solutions WAVE PTX, motorolasolutions.com, read 2026-10-17
  3. TASSTA, tassta.com, read 2026-10-10

Related comparisons