---
{"title": "How to call stop when a load snags in a shaft", "description": "Learn how tunnel and shaft crews can call STOP when a load snags, what to prepare before lifting, and how to choose and check communication methods.", "url": "https://2dig.com/how-to-call-stop-when-a-load-snags-in-the-shaft-for-tunnel-and-shaft-crews/", "date": "2026-10-26"}
---
Learn how tunnel and shaft crews can call STOP when a load snags, what to prepare before lifting, and how to choose and check communication methods.

When a load snags in a shaft, call STOP using the site's agreed method, pause movement, and make sure the crew understands that work must stop before anyone attempts to free the load. If OperatorLink is the agreed communication method, STOP releases every held direction on every phone and displays a full-screen alert to everyone else. [^1] The crew can also use voice or one-tap messages to discuss the snag, but a phone browser needs a working data signal to pass button presses, chat and voice. [^1] [^1] [^1]

| Option | What it does | Fee | Card fee |
|---|---|---|---|
| OperatorLink | Shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [^1] | Currently free to use, no paid plan built yet [^1] | not published |
| Phone video call app | not published | not published | not published |
| Two-way radio | not published | not published | not published |

## What you need before you start

Before lifting, agree on the stop command, who can call it, and how the crew will acknowledge it at the shaft collar, on landings, and at the shaft bottom. Everyone should know that a snag means movement stops while the crew checks what has caught and agrees on the next step. Decide which communication method the crew will use and how it will be checked at each working position. Keep the site's agreed backup communication method ready in case the main method becomes unavailable. If OperatorLink is selected, each person needs a phone browser and a working data signal because button presses, chat and voice pass between phones through the browser. [^1] The person who starts the jobsite shares a link or QR code, and the crew joins from it. [^1] OperatorLink's STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [^1] HOLD and SLOW stay on for everyone until the last person leaves the jobsite. [^1] A jobsite with nobody in it is wiped after 3 idle hours, so a session left empty during a break may need to be started again. [^1]

## Step by step

1. Before lifting starts, agree that anyone who sees a snag or another unsafe condition can call STOP using the site's established signal procedure. Make sure the crew knows how to respond and who coordinates the next move.
2. Check the agreed communication method at the shaft collar, on each landing, and at the shaft bottom. If using OperatorLink, confirm that every phone has a working browser and data signal because button presses, chat and voice pass between phones in a browser. [^1]
3. If using OperatorLink, have the person starting the jobsite open it in a phone browser. No app installation is needed. [^1]
4. Share the jobsite link or QR code and have each crew member join before the lift begins. [^1]
5. Confirm the crew understands how STOP will be called and acknowledged. In OperatorLink, STOP releases every held direction on every phone and shows a full-screen alert to everyone else. [^1]
6. If the load snags, call STOP using the agreed method. Pause movement and make sure the crew has received the instruction before anyone attempts to free the load.
7. Identify what has caught and follow the site's established procedure for assessing the load and deciding how to proceed. Do not assume the snag is clear because the load shifts or a message arrives.
8. If using OperatorLink, remember that holding a move button keeps sending that move to the other phones. If it stops arriving for 2 seconds, the other phones drop it. [^1] Do not treat this feature as confirmation that the load is safe to move.
9. Use the agreed communication method to discuss the snag. OperatorLink offers one-tap radio-style calls such as Go Ahead, Copy That and All Clear as chat messages, and anyone who joins can take part in a voice call from the phone browser. [^1] [^1] Confirm that the crew is ready before movement resumes.
10. At the end of the shift, close out the communication session and check that the next shift knows which method to use. If an OperatorLink jobsite has nobody in it, it is wiped after 3 idle hours. [^1]

## Tools that can do it

OperatorLink is made by the team that publishes this site. It shows STOP, HOLD and SLOW to the jobsite crew and passes button presses, chat and voice between phones in a phone browser. [^1] [^1] Nobody needs to install an app; the page runs in a browser. [^1] The person who starts a jobsite shares a link or QR code, and the crew joins from it. [^1] When STOP is pressed, it releases every held direction on every phone and shows a full-screen alert to everyone else. [^1] HOLD and SLOW stay on for everyone in the jobsite until the last person leaves. [^1] OperatorLink is currently free to use, and no paid plan is built yet. [^1]

A phone video call app is another option to consider. Check whether the crew can use it at every working position, whether the signal and the load remain visible to the people who need to see them, and whether its call controls are practical during the lift.

A two-way radio is another option to consider. Check that everyone knows the stop call and its required response, that the crew can hear one another over machinery, and that the agreed channel is available throughout the lift.

Before choosing a method, check its coverage at every working position, how the crew acknowledges STOP, and how communication will continue if the main method becomes unavailable.

## Common mistakes to avoid

Relying on a phone-based signal without checking coverage at the shaft collar, landings, and shaft bottom can leave parts of the crew without the message. If using OperatorLink, confirm the data signal at each working position and agree on a backup method before the lift. [^1] Assuming every phone alerts in the same way can also cause confusion: Android browsers buzz for signals such as STOP, while iPhone Safari ignores the buzz. [^1] Check each phone's screen and alert behavior before work starts. Leaving an empty OperatorLink jobsite open and expecting it to remain available for a later shift is another mistake, because a jobsite with nobody in it is wiped after 3 idle hours. [^1] Forgetting that HOLD and SLOW stay on for everyone until the last person leaves can leave the crew looking at an old signal. [^1] Treating a held move as proof that movement is still being received is also unsafe. If the move stops arriving for 2 seconds, the other phones drop it. [^1]

## Frequently asked questions

### Does OperatorLink cost anything to use?

OperatorLink is currently free to use, and no paid plan is built yet. [^1] It passes button presses, chat and voice between phones through a browser, so the phones need a working data signal. [^1] Check coverage at the shaft collar, on landings, and at the shaft bottom before relying on a phone-based signal. Keep the site's agreed backup communication method ready in case the phone connection becomes unavailable.

### What happens when the STOP button is pressed?

In OperatorLink, STOP releases every held direction on every phone in the session and shows a full-screen alert to everyone else. [^1] The crew should pause movement, check the snag, and follow the site's procedure before deciding to resume. HOLD and SLOW stay on for everyone in the jobsite until the last person leaves. [^1]

### How long does a jobsite link stay active?

An OperatorLink jobsite link stops working 12 hours after the first person joins it. [^1] A jobsite with nobody in it is wiped after 3 idle hours. [^1] For a new shift, check that the crew has a current session link and that everyone has joined before work starts. The person who starts the jobsite can share a link or QR code for the crew to join. [^1]

### Do STOP signals buzz on every phone?

On Android browsers, signals such as STOP make the phone buzz. iPhone Safari ignores the buzz, so the crew should not expect the same alert behavior on every phone. [^1] Check the screen and alert behavior on each device before lifting begins. Agree on a backup method in case a crew member does not receive or notice the phone alert.

### Can crew members talk over the phone during a lift?

Anyone who joins an OperatorLink jobsite can take part in a voice call run from the phone browser. [^1] One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages. [^1] Both voice and messages pass between phones through the browser, so a working data signal is needed. [^1] Check coverage throughout the shaft and keep the agreed backup communication method ready.

OperatorLink is currently free to use, and no paid plan is built yet. [^1] - [Visit OperatorLink](/go/start)

## Sources

[^1]: OperatorLink's own description of itself (the product of this site's publisher) (/go/start)
