ESChat vs Motorola Solutions WAVE PTX in 2026
A crane crew choosing among ESChat, Motorola Solutions WAVE PTX and OperatorLink: what each does, published prices, jobsite setup, and how to choose.
2Dig is published by the makers of OperatorLink, which is compared here alongside other tools.
This page sets out what ESChat, Motorola Solutions WAVE PTX and OperatorLink each do for a crane crew member, what they cost as published, and how each is set up. The facts cited for the two rivals are fewer, so this page says less about them. Where a rival's sources are silent on a point, the page says what to check instead.
| Option | Own fee | Card fee |
|---|---|---|
| ESChat | $5.99 per user per month, with a 10% discount [1] [1] | not published |
| Motorola Solutions WAVE PTX | not published | not published |
| OperatorLink | Free to use; no paid plan is built yet [2] | not published |
The short answer
A crane crew member needs a signal to reach the whole crew at once while the crane moves. OperatorLink shows STOP, HOLD and SLOW to the crew and passes button presses, chat and voice between phones in a browser [2]. ESChat offers a cloud hosted service [1]. The ESChat facts gathered for this page do not describe how that service passes signals to a crew, so check that with ESChat directly. Motorola Solutions' cited facts describe an APX P25 radio portfolio built to streamline mission-critical communications [3]. Those facts do not say how WAVE PTX passes signals, so a crew with that need should check it directly with Motorola Solutions. For a crew that needs a STOP on every phone, OperatorLink's sources describe one [2].
What ESChat, Motorola Solutions WAVE PTX is built for
The ESChat facts gathered for this page are few, so this page says little about what that service is built for. Motorola Solutions says its command center software offers what it calls the industry's only complete, 360° incident view, from call to case closure [3]. Its video security systems are powered by AI analytics that Motorola Solutions describes as responsibly built [3]. Its APX P25 radio portfolio was built to streamline mission-critical communications [3]. None of these Motorola Solutions facts describes how WAVE PTX passes signals or button presses to a crew, so this page does not say what it does for a crew's signals. A crew reading this should expect that answer to come from the company's own documentation rather than from this page.
What OperatorLink is built for
OperatorLink is made by the team that publishes this site. For a crane crew member, it shows STOP, HOLD and SLOW to the jobsite crew, and passes button presses, chat and voice between phones in a browser [2]. A STOP releases every held direction on every phone and shows a full-screen alert to everyone else [2]. HOLD and SLOW stay on for everyone in the jobsite and are cleared when the last person leaves [2]. Holding a move button keeps sending that move to the other phones, and if the move stops arriving for 2 seconds, the other phones drop it [2]. One-tap radio-style calls such as Go Ahead, Copy That and All Clear are sent as chat messages [2]. Anyone who joins can take part in a voice call run from the phone browser [2].
Pricing and fees
ESChat's cloud hosted service costs $5.99 per user per month [1]. The price is per user, so the total for a crew depends on how many people use the service [1]. The ESChat page lists a 10% discount [1]. The facts gathered for this page give no price for Motorola Solutions WAVE PTX, so none is stated here. OperatorLink is currently free to use, and no paid plan is built yet [2]. A card fee is not published for any of the three, so a crew that expects to pay one should ask each provider before choosing. Prices can change, so check each one before the crew commits.
Setting it up on a jobsite
OperatorLink runs in a phone browser with no app install [2]. The person who starts a jobsite shares a link or QR code, and the crew joins from it [2]. Phones can add the app to their home screen as a standalone app [2]. A jobsite link stops working 12 hours after the first person joins [2], and a jobsite with nobody in it is wiped after 3 idle hours [2]. Button presses, chat and voice pass between phones in the browser [2]. The ESChat facts gathered for this page do not describe how a crew gets onto the service or how signals pass, so check both with ESChat before a shift. The Motorola Solutions facts gathered here describe radios, video security and command center software, not how a crew is set up on WAVE PTX, so check that with Motorola Solutions.
Things to check before you choose
Which signals does the crew need on a jobsite, and how will you test that each tool passes them before a lift? Do the crew's phones run Android or iPhone? On Android browsers a signal such as STOP makes the phone buzz, but iPhone Safari ignores the buzz [2]. Decide whether a buzz alert matters for your crew. Does a jobsite link that stops working 12 hours after the first person joins suit your shifts [2]? Multiply the price of $5.99 per user per month for ESChat by the number of people on the crew, and check whether the 10% discount applies to the plan you need [1] [1]. What Motorola Solutions charges for WAVE PTX, and what that price would cover, is not in the facts gathered here, so ask the company before comparing.
How to choose
If a crew needs a STOP that reaches every phone, OperatorLink's sources describe a STOP that releases every held direction and shows a full-screen alert to everyone else [2]. If a crew needs HOLD and SLOW to stay on for everyone until the last person leaves, OperatorLink's sources describe that too [2]. If a crew needs a free start, OperatorLink is currently free to use [2], and ESChat's cloud hosted service costs $5.99 per user per month [1]. If a crew needs a radio line, Motorola Solutions' cited facts describe an APX P25 radio portfolio built to streamline mission-critical communications [3]. Those facts do not say how WAVE PTX passes signals, so a crew with that need should check it directly. A crew that needs both signals on phones and a radio line should check each option against both needs, because no single cited source covers both.
Frequently asked questions
Is OperatorLink free to use?
OperatorLink is currently free to use, and no paid plan is built yet [2]. The sources cited on this page give no price beyond that, and a card fee is not published for it. Prices can change, so confirm the current terms with the product before a shift, and ask whether any future plan would change what the crew pays.
How much does ESChat cost for commercial customers?
ESChat's cloud hosted service costs $5.99 per user per month [1]. The ESChat page lists a 10% discount [1]. Because the price is per user, the monthly total for a crew depends on how many people use the service. A card fee is not published, so ask ESChat about that before paying.
Does OperatorLink work on iPhone?
OperatorLink runs in a phone browser with no app install [2]. A phone can add it to the home screen as a standalone app [2]. On Android browsers, signals such as STOP make the phone buzz, but iPhone Safari ignores the buzz [2]. A crew with iPhones should check whether the on-screen alert is enough for its needs.
Does Motorola Solutions WAVE PTX publish its prices?
The facts gathered for this page give no price for Motorola Solutions WAVE PTX, so this page does not state one. Check the company's pricing directly before comparing it with the other two options. Ask what any quoted price would cover before deciding.
How long does an OperatorLink jobsite link last?
A jobsite link stops working 12 hours after the first person joins it [2]. A jobsite with nobody in it is wiped after 3 idle hours [2]. The person who starts a jobsite shares a link or QR code, and the crew joins from it [2]. A crew whose shift runs past 12 hours should start a new jobsite with a fresh link. [2]
OperatorLink is currently free to use, and no paid plan is built yet. [2]
Try OperatorLinkSources
Related comparisons
- Push-to-talk apps for crane crews compared (2026)
- Push-to-talk apps for aircraft recovery crane crews
- Push-to-talk apps for crane crews for apprentice riggers
- Push-to-talk apps for boom truck crane crews in 2026
- Push-to-talk apps for bridge construction crane crews
- Push-to-talk apps for crane crews on bridge inspection jobs
- Push-to-talk apps for bulk material handlers on cranes compared
- Push-to-talk Apps for Concrete Pump Crews in 2026
- PTT apps for crane crews for construction foremen
- Push-to-talk Apps for Crane Crews in 2026